Pioneer AVH-P4900DVD - DVD Player With LCD Monitor Panduan Instalasi - Halaman 2
Jelajahi secara online atau unduh pdf Panduan Instalasi untuk Pemutar DVD Pioneer AVH-P4900DVD - DVD Player With LCD Monitor. Pioneer AVH-P4900DVD - DVD Player With LCD Monitor 9 halaman. Av receiver/dvd player
Juga untuk Pioneer AVH-P4900DVD - DVD Player With LCD Monitor: Panduan Servis (9 halaman)
Halaman Cetak
Connecting the Units
Connecting the Units
Connecting the power cord
15 cm (5-7/8 in.)
IP-BUS input (Blue)
This product
Multi-CD player
(sold separately)
IP-BUS cable
Yellow/black
If you use an equipment with Mute function, wire this lead to the
Audio Mute lead on that equipment. If not, keep the Audio Mute lead
free of any connections.
Red
Fuse resistor
Connect to terminal controlled by ignition switch (12 V DC).
Violet/white
Of the two lead wires connected to the back lamp, connect the one in which the
voltage changes when the gear shift is in the REVERSE (R) position.
For details, see Fig. 4
Yellow
Fuse holder (10 A)
Connect to the constant 12 V supply terminal.
Black (chassis ground)
Connect to a clean, paint-free metal location.
Gray
White
+
+
Front speaker
≠
≠
Gray/black
White/black
Left
Violet
Green
+
+
Rear speaker
≠
≠
Green/black
Violet/black
Antenna cable
15 cm (5-7/8 in.)
Connection method
1.
Clamp the lead.
Note:
• The position of the parking brake switch depends
on the vehicle model. For details, consult the
vehicle Owner's Manual or dealer.
WARNING
LIGHT GREEN LEAD AT POWER CONNECTOR IS DESIGNED TO
DETECT PARKED STATUS AND MUST BE CONNECTED TO THE
POWER SUPPLY SIDE OF THE PARKING BRAKE SWITCH. IMPROPER
CONNECTION OR USE OF THIS LEAD MAY VIOLATE APPLICABLE
LAW AND MAY RESULT IN SERIOUS INJURY OR DAMAGE.
Light green
Power supply side
Used to detect the ON/OFF status of the parking brake.
This lead must be connected to the power supply side of
the parking brake switch.
Ground side
Blue/white
Connect to system control terminal of the power amp or
auto-antenna relay control terminal (max. 300 mA 12 V DC).
Front speaker
With a 2 speaker system, do not connect anything
Right
to the speaker leads that are not connected to speakers.
When you connect separately sold multi-channel processor
Rear speaker
(DEQ-P8000) to this unit, do not connect anything to the
speaker leads and system remote control (blue/white).
When connecting to separately sold power amp
This product
2. Clamp firmly with
needle-nosed
pliers.
Parking brake
switch
Fig. 2
Subwoofer output
or non fading output
(SUBWOOFER OUTPUT or
NON-FADING OUTPUT)
23 cm (9 in.)
Rear output
RCA cables
(REAR OUTPUT)
15 cm
(sold separately)
(5-7/8 in.)
Front output
(FRONT OUTPUT)
15 cm
(5-7/8 in.)
Blue/white
System remote control
Connect to system control terminal of the
power amp (max. 300 mA 12 V DC).
Left
When you connect separately sold
multi-channel processor (e.g. DEQ-P8000)
Front speaker
to this unit, do not connect anything to the
speaker leads and system remote control
(blue/white).
Note:
When you connect multi-channel processor to
Rear speaker
this unit, separately sold power amp must be
connected to multi-channel processor.
Note:
Change the initial setting of this product
Subwoofer
(refer to the Operation Manual).
The subwoofer output of this unit is monaural.
<ENGLISH>
ENGLISH
Power amp
(sold separately)
Power amp
(sold separately)
Power amp
(sold separately)
Right
+
+
Front speaker
≠
≠
+
+
Rear speaker
≠
≠
+
+
Subwoofer
≠
≠
Perform these connections when using
the optional amplifier.
Fig. 3