Pioneer S-H810V Buku Petunjuk

Jelajahi secara online atau unduh pdf Buku Petunjuk untuk Sistem Pembicara Pioneer S-H810V. Pioneer S-H810V 9 halaman. Pioneer speaker system instruction manual

Halaman Cetak

1. Specifications

English

BEFORE OPERATION

Thank you for buying this PIONEER product.

Read the Instruction Manual carefully before using this speaker system so that

you can operate it properly. After you have finished, put this manual away in a

safe place for future reference.

The rated impedance of this speaker system is 6 . It must be connected to a

amplifier which accepts this type of load (miminum and maximum impedances

accepted by the amplifier are generally indicated near the loudspeaker outlets: for

example "4

to 16 " or "6

to 16 ").

To guard against damage to this speaker system due to an electric power

overload, take the following precautions:

Do not supply more than the maximum permitted power to the speaker

system (see Specifications).

Any connection or switching on or off of part of the audio system (CD

player, tuner etc.) must be carried out after switching off the amplifier or at

least with the loudspeaker outlets disconnected (if the amplifier allows).

Interference caused by these operations will otherwise reach the speaker

and may damage the treble loudspeaker units.

When boosting particular frequencies using a graphic equaliser or bass

and treble correctors, make sure that you do not increase the amplifier

volume excessively, as the speaker will be overloaded more quickly.

Do not force a low-power amplifier to produce a high level of sound as

harmonic distortion increases rapidly in this situation and may pose a

danger to the treble speaker units.

Avoid touching the diaphragms and suspensions of speakers units as they are

fragile.

The speaker units in this speaker system are magnetically shielded.

However, colours may blur if the speakers are positioned too close to a

television screen. If this happens, switch off the television and switch it

back on again after 15 to 30 minutes. If the problem persists, move the

speakers away from the television set.

INSTALLATION

In order to minimize the transmission of vibrations from the speaker to the floor,

Pioneer offers two possibilities :

4 foam cushions to be stuck on the

underside of the speaker system.

4 metal decoupling spikes to be

screwed under the speaker system

(after having unscrewed the 4 metal

feet).

If desired (especially with polished

wood floors), you can also employ the

4 provided metal bases between the 4

decoupling spikes and the floor.

This speaker system is heavy and fragile, and it is therefore dangerous to install it

in an unstable position. For added safety, it is advisable to attach these speakers

to a wall or pillar using chains and hooks (not supplied). To do so, screw the

provided metal ring to the back of the speaker cabinet and then pass a chain or

cable through the metal ring.

ADVICES AND PRECAUTIONS :

For optimum sound reproduction of high frequencies, the treble speaker units

must be at the same height as the listener's ears.

For low frequencies, it is possible to increase the level of bass sounds by

positioning the speakers close to a wall (the maximum increase being obtained

for a position in a corner of the listening room).

Do not install the speakers close to an oven or heating appliance. Avoid

exposing them to direct sunlight. High temperatures can distort the structure of

the enclosure and adversely affect the sound.

SPEAKER SYSTEM

ENCEINTE ACOUSTIQUE

LAUTSPRECHERSYSTEM

SISTEMA ALTOPARLANTE

LUIDSPREKERSYSTEEM

HÖGTALARSYSTEM

SISTEMA DE ALTAVOCES

SISTEMA DE ALTIFALANTES

Discover the benefits of registering your product online at

http://www.pioneer.co.uk (or http://www.pioneer.eu)

CONNECTIONS

Switch off the amplifier power supply (OFF).

Connect the cables to the input terminals on the rear of the speaker: Connect

the neutral cable to the HF

Connect the cables to the loudspeaker outlet terminals of the amplifier. Connect

the live cable to the

REMARKS :

For a bi-wiring connection, first remove the cables which link the two pairs of

input terminals labelled HF

Check that the cables are securely connected to the terminals. A loose

connection may cause not just intermittent or distorted sound but short-circuiting

and breakdown of the amplifier.

If the cables of one of the speakers have been connected with the wrong

polarities, you will find when listening to a stereo recording that bass sounds are

weakened and the stereo effect normally obtained between the two speakers

does not exist.

MAINTENANCE OF THE ENCLOSURE

Use a cloth to wipe away dust and dirt.

If the enclosure is very dirty, wipe with a soft cloth dipped in a neutral detergent

diluted five to six times with water, then wipe again with the dry cloth. Do not use

thinner, benzene, cleaning sprays or other chemical products on or near the

enclosures as the surfaces could be adversely affected.

SPECIFICATIONS

Speaker ............................................................... Floor-standing type, bass-reflex

System ............................................................................. 4 ways, 5 speaker units

Speaker units :

Nominal Impedance ...................................................................................... 6

Frequency range ................................................................ 35 Hz to 100 000 Hz

Sensitivity ..................................................................... 89 dB/W at 1 m distance

Maximum power ........................................................................................ 130 W

Dimensions....................................... 250 mm (W) x 1190 mm (H) x 300 mm (D)

Weight .......................................................................................................... 25 kg

Accessory parts

Instruction Manual ................................................................................................ 1

Warranty ............................................................................................................... 1

Foam cushions .................................................................................................... 4

Decoupling spikes + base ................................................................................... 4

Ring + screw ........................................................................................................ 1

This product may be covered by one or more of the following patents owned by

GP Acoustics (UK) Ltd. and its affiliates: [Japanese Patent No. 2766862, United

Kingdom Patent No. GB 2 236 929 A, and the United States Patent No.

5,548,657]. To the extent of such coverage, this product has been licensed by

GP Acoustics (UK) Ltd. KEF and UNI-Q are registered trademarks of the GP

Acoustics family of companies.

REMARK : The specifications and design of this product are subject to change

without notice, in the interests of improvements.

INSTRUCTION MANUAL

MODE D'EMPLOI

BEDIENUNGSANLEITUNG

GUIDA PER L'USO

GEBRUIKSAANWIJZING

BRUKSANVISNING

GUIA DE OPERACIÓN

GUIA DE OPERAÇÃO

or LF

terminal.

terminal and the neutral cable to the

and LF

Woofers ................................................ Cone type, 130 mm x 2

Medium ....................................................... Cone type, 130 mm

Tweeter ......................................................... Dome type, 25 mm

Super-Tweeter ................................... Riffel type, 8 mm x 46 mm

Published by Pioneer Corporation.

2007 Pioneer Corporation.

All reproduction and translation rights reserved.

Printed in China <FRRD-208-B>

http://www.pioneer.co.uk

http://www.pioneer.eu

terminal and the live cable to the HF

Strip the insulation at the tip of the cord

and twist the strands.

Turn the thumbscrew anti-clockwise,

make sure that the speaker cord is

inserted well into the hole and turn the

thumbscrew clokwise to fasten into

position.

Connect the hot-side speaker cord to the

or LF

terminal.

Connect the common-side speaker cord

to the HF

of LF

terminal.

, and HF

and LF