Dinex CARLISLE Turbo-Temp DX1011208 Panduan Pengoperasian & Pemeliharaan - Halaman 2
Jelajahi secara online atau unduh pdf Panduan Pengoperasian & Pemeliharaan untuk Pengisi Daya Baterai Dinex CARLISLE Turbo-Temp DX1011208. Dinex CARLISLE Turbo-Temp DX1011208 8 halaman.
Halaman CetakINTRODUCTION
Congratulations! You have purchased the new Dinex
Induction Charger. Your Dinex Turbo•Temp induction heated base
system, when used within a controlled hot food trayline process and
covered with Dinex insulated domes, will keep hot plated food satisfying
for up to one hour from plating.
Please read this manual for helpful guidelines on how to use your new
equipment. Should you have any questions concerning the equipment,
please call Dinex Service at
1.888.673.4639.
!
IMPORTANT: For your safety, read and follow all cautions,
information, and warnings.
FREIGHT DAMAGE CLAIMS
Your Turbo•Temp Induction Charger was carefully inspected and packed
before leaving our factory. The transportation company assumes full
responsibility for the safe delivery of this equipment. Dinex cannot
assume responsibility for damage or loss incurred during transit. Visible
damage or loss should be noted on the freight bill and signed by the
person making the delivery.
A freight claim should be filed immediately with the transportation
company. If damage is unnoticed or concealed until the equipment is
unpacked, notify the transportation company immediately and tell them
you want to file a concealed damage claim. This must be done within
fifteen (15) days after delivery was made. Be sure to retain all packing
materials and cartons.
!
ATTENTION: Use of this symbol identifies a potentially hazardous
situation which, if not avoided, may result in damage to the machine
or injury to the operator.
!
CAUTION: If the product is used without observing the information
given under this symbol, minor personal injury, or damage to
equipment may result.
!
ATTENTION: Installation of this equipment should be performed
only by persons qualified or licensed to install electrical equipment.
• Adjustments and service work should be performed only by
qualified service technicians.
• This equipment is intended for commercial use only. Not for
household use.
• Use of other than genuine Dinex replacement parts or service
work performed by those other than authorized Dinex service
agents will void the warranty.
• Do not use corrosive cleaners on the equipment. Use
only mild detergents.
APPLICATION & USE
The equipment is for commercial use in the foodservice industry. It
provides maximum induction heating compatible with Dinex bases. Use
with Dinex Smart bases only.
SAFETY
The instructions contained in this manual provide important guidelines
for the equipment user regarding correct and safe installation. Particular
attention should be paid to the precautions given in various parts of
this manual. Do not attempt to repair this equipment. Repairs must be
performed by authorized personnel only.
• Never use the equipment as a work surface or cutting board.
• Do not attempt to heat anything other than a Dinex base.
!
®
Turbo•Temp™
IMPORTANT: Do not place a Smart base in a microwave oven.
!
INFORMATION: This appliance is for commercial use only and must
be used exclusively for the purposes prescribed.
!
IMPORTANT: The following instructions reduce the risk of fire,
electrical shock, or injury.
SET UP
1. Carefully remove any packing material from the induction charger
and check loose packing material for small parts or accessories.
Inspect the charger for concealed damage before placing packing
material aside. Keep the packaging until you are confident with the
equipment performance.
2. The Turbo•Temp induction charger is equipped with a locking plug.
This plug is part of a system that will protect you from injury in the
event of an electrical malfunction inside the unit. Be sure the plug is
fully plugged into a matching socket that is properly grounded.
!
ATTENTION: DO NOT cut or break off the larger angled prong on
this plug, or change the plug or power in any
way. Doing so will create a safety hazard and also void
the warranty.
3. MAKE SURE THAT INCOMING VOLTAGES MATCHES THE
CHARGER REQUIREMENTS. A product identification label on the
bottom of the unit specifies the operating voltage, current, frequency,
phase, and maximum wattage of the charger. Plugging or wiring
the charger into less voltage than the charger is rated may
significantly decrease the performance of the unit or damage
internal electrical components.
4. Do not place foreign objects on the charger, or between the Dinex
base and the charger surface. Foreign objects may heat within the
induction field and cause damage to the charger surface and/or
base.
5. Do not use any Turbo•Temp charger that has a damaged cord or
plug. Consult the warranty and follow the instructions for service.
6. Do not let the power cord touch hot surfaces.
7. The center of the charger may get hot to the touch after hours of
continuous use. Use caution when loading and unloading bases.
8. The charger requires ample air flow to cool the internal electronic
components. Air is pulled in from the front and sides of the bottom
of the unit and is exhausted towards the rear of the unit. Assure that
nothing obstructs the airflow around all four sides of the unit. Allow at
least two inches from a wall or partition.
9. A dedicated electrical circuit is recommended for each Turbo•Temp
charger.
!
IMPORTANT: Every installation site has different electrical wiring
requirements. Because many different local codes exist, it is the
owner and installer's responsibility to comply with all federal, state,
and local codes. Dinex is not responsible for any consequential
damages, either expressed or implied, as a result of failure to
comply with installation requirements.
Turbo•Temp | 2