Aeotec Multisensor Gen5 Panduan Pengguna
Jelajahi secara online atau unduh pdf Panduan Pengguna untuk Sensor Keamanan Aeotec Multisensor Gen5. Aeotec Multisensor Gen5 2 halaman.
Halaman CetakAeotec by Aeon Labs MultiSensor.
Motion sensor. Humidity sensor. Thermometer. Light sensor.
The corner of your room just got smart.
Aeotec by Aeon Labs' MultiSensor looks like a motion sensor and it acts like one
too. But it's also so much more. Installing this 1 piece of Z-Wave® technology is
the same as installing 4 pieces of Z-Wave technology. Your home control network
will immediately understand motion, temperature, humidity and light readings
wherever MultiSensor installed. Those intelligent readings will equate to intelligence
automation. And intelligent automation will give you the perfect, smart home.
Familiarize yourself with your MultiSensor.
Your MultiSensor comes packaged with a number of accessories that will help with
its installation and operation.
View the expanded manual:
http://aeotec.com/support
Your MultiSensor can be powered by battery or by USB with an appropriate adaptor.
For the purposes of installation and setup, and even if you intend to power your
sensor with batteries, we recommend utilising the provided USB cable for setup.
For this you'll need an adaptor to plug your USB cable into, this can include any
USB port on a computer and most mobile phone chargers. These first steps can be
performed in any location with your home, and not necessarily in your MultiSensor's
final installation location.
For a USB powered installation;
1. Remove the rear part of your sensor by twisting the battery cover in a counter-
clockwise motion and separating the two parts of your sensor.
2. Insert the appropriate end of the provided USB cable into your sensor's USB port.
Your MultiSensor is now powered on.
For a battery powered installation;
1. Remove the rear part of your sensor as shown in the previous step 1.
2. Insert 4 AAA batteries oriented according to the picture below. Your MultiSensor is
now powered on.
Quick start.
Setup your power.
Add your MultiSensor to your Z-Wave network.
It's now time to sync your MultiSensor with a Z-Wave network. The following
instructions explain how to do this using a Z-Stick or a Minimote from Aeotec. If
you're using an alternative controller for your Z-Wave network, please refer to its user
manual for network inclusion instructions.
If you're using a Z-Stick:
1. Take your Minimote to your MultiSensor.
2. Press the Include button on your Minimote.
3. Press the Z-Wave Button on your MultiSensor.
4. You can test if your MultiSensor has been successfully synced with your Z-Wave
network by pressing its Z-Wave Button. If you press the button and your sensor's
LED illuminates for a few seconds, then syncing has been successful. If the LED
blinks when the button is pressed, the syncing has been unsuccessful and you
Action Button
should repeat the above steps.
5. Press any button on your Minimote to return it to standard operating mode.
Selecting a location for your MultiSensor .
MultiSensor can bring its intelligent readings to many locations of your home. That
includes outside of your home. MultiSensor is weatherized and can operate outdoors
1. If your Z-Stick is plugged into a gateway or a computer, unplug it.
in elements such as rain and snow. Please note that when installed outdoors, your
2. Take your Z-Stick to your MultiSensor .
MultiSensor should only be relied on for temperature, light and humidity readings
3. Press the Action Button on your Z-Stick.
and that the motion sensing capabilities should be disabled on your gateway in order
4. Press the Z-Wave Button on your MultiSensor .
to avoid false readings.
5. You can test if your MultiSensor has been successfully synced with your Z-Wave
network by pressing its Z-Wave Button. If you press the button and your sensor's
While light can impact on the quality of motion readings, it's also important to
LED illuminates for a few seconds, then syncing has been successful. If the LED
understand things that may impact on other readings within your home. Specifically,
blinks when the button is pressed, the syncing has been unsuccessful and you
your MultiSensor should not be installed in areas of artificial temperature change.
should repeat the above steps.
Thus, when selecting a location, avoid placing it beside or near air conditioners,
6. Press the Action Button on the Z-Stick to return it to standard operating mode.
humidifiers, and heaters, and avoid positioning it directly opposite a window or direct
Return it to your gateway or computer.
sunlight.
Selecting a location for your MultiSensor to be installed depends on the use case.
If you're using a Minimote:
Whatever the case or the installation location, please ensure that it fits with your
sensor's effective motion sensing range as described in these diagrams.
For ceiling mounting using the Back-Mount Plate:
If selecting an outdoor location, it's important to position your MultiSensor in a
sheltered location. It is best if your MultiSensor is not directly exposed to rain and
integral that the humidity venting on your MultiSensor neer is. As such,during
installation you should orient your MultiSensor according to the following diagram so
that the sensor perforations on the side of your sensor are facing downwards.
For wall mounting using the Back-Mount Arm:
Physically install your MultiSensor .
With your MultiSensor now part of your Z-Wave network, it's time to finish its physical
installation.
There are 2 ways that your MultiSensor can be mounted on on a wall or ceiling.
Using the Back-Mount Plate, you can mount it flat against a wall or ceiling. Using the
Back-Mount Arm you can mount it on a surface or in a corner and angle it as desired.
To physically install your MultiSensor;
Further, for optimal performance your MultiSensor should NOT be mounted directly
1. Reattach the two parts of your MultiSensor to each other. To do this, align the
on or near metal framing or other large metallic objects. Large metal objects may
lock/unlock half-dimple markers that are under the unlock symbol and then twist in
weaken the Z-Wave wireless signal.
a clockwise motion.
2. If used the USB cable to power your MultiSensor, ensure that power can be
provided to your desired installation location. Please note that when installed in
areas that where the temperature can drop below-10°C, it is advised that mains
power is used and battery power is not.
3. Attach your desired mounting accessory. This can be the Back-Mount Plate or the
Back-Mount Arm.
4. If using the Back-Mount Plate, utilize the provided 3mm screws to affix it to a surface.
5. If using the Back-Mount Arm, utilize one 3x10mm screw to attach the Back-Mount
Plate to the Back-Mount Arm. Then affix the Back-Mount Arm to a surface utilizing
the provided 3x20mm screws.
6. The Back-Mount Arm may be locked at various angles by turning the Friction Lock
clockwise and counter-clockwise to respectively tighten or loosen the angle of the
arm.