Whirlpool AWE 8727 Bagan Program - Halaman 2

Jelajahi secara online atau unduh pdf Bagan Program untuk Mesin cuci Whirlpool AWE 8727. Whirlpool AWE 8727 2 halaman.

1
2

CONSUMPTION DATA

Temperature

Programme

(°C)

White Cotton / Antibacterial

95

Cotton

60

Cotton with "Eco"***

60

Cotton

40

Synthetics

60

Synthetics

40

Daily load

40

Quick wash

30

Delicates

40

Baby

40

Handwash

40

Wool

40

Lingerie

30

Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home

may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.

*

The time indicated on the display can deviate from the values in the table, because it takes into account the household

conditions applicable at that time.

**

To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.

***

Reference Programme for Energy Label.

ADD DETERGENTS, CLOSE THE LID AND

SELECT THE PROGRAMME

Add detergent as indicated on the front page and as

described in the chapter "Detergent and Additives"

in your Instructions for Use.

1. Turn the programme selector to the desired

programme. The display shows the programme

duration in hours and minutes as well as the

predefined temperature. The "Start/Pause"

button flashes.

2. The temperature can be altered by pressing

the "Temperature" button.

3. The indication lamp of the predefined spin speed

lights up; in case you want to set another spin

speed, press the "Variable spin" button.

SELECT ANY DESIRED OPTION

Push the button(s) of any option(s) desired - the

respective indication lights up.

When the combination of programme and additional

option(s) is not possible, the indication lights switch off

automatically. Unsuitable combinations of options are

deselected automatically.

"Eco" button

• With a modified temperature profile and a slightly

prolonged washing duration, the optimum

combination of excellent washing result and even

lower energy consumption is achieved.

"Easy ironing" button

• Can be used together with "Cotton",

"Synthetics" and "Daily load" programmes to

make ironing easier.

Load

Water

Energy

Approx. Programme Duration

(kg)

(l)

(kWh)

(hours : minutes)*

5.5

55**

1.70

1:55

5.5

49

1.02

2:25

5.5

49

0.93

2:35

5.5

53

0.55

2:00

2.5

53**

0.85

1:30

2.5

47

0.50

1:15

3.0

43

0.48

1:00

3.0

36

0.30

0:30

1.5

51

0.50

0:45

5.5

73

0.55

2:15

1.0

43

0.50

0:35

1.0

53

0.50

0:45

1.0

42

0.30

0:35

• Increases the water quantity and the clothes are

spun very gently.

"Prewash" button

• Only for heavily soiled loads (for example sand,

granular dirt) sensible. Increases the cycle time

by approximately 15 min.

• Do not use liquid detergent for the main wash

when activating the Prewash option.

"Intensive rinse" button

• More water is added and rinse cycle is prolonged.

• This option is particularly suitable for areas with

very soft water, for washing baby linen and

helping people with allergies.

"Rinse hold" button

• The laundry remains in the last rinse water

without progressing to the final spin cycle to avoid

creasing and prevent colours from changing.

• This option is particularly recommended for the

programmes "Synthetics", "Daily load" and

"Delicates".

• It is particularly useful if you want to postpone

spinning to a later time, or if you want to drain only.

• If you select "Rinse hold", do not leave the laundry

to soak for too long.

Note: The programme stops to "Rinse hold" at

the time the "Rinse hold" light in the programme

sequence indicator is on. The indication lamp

next to the "Start/Pause" button flashes.

Terminate the "Rinse hold" option:

• Press the "Start/Pause" button; the

programme will terminate automatically with the

final spin cycle for the present wash programme.

• If you do not wish to spin the clothes, turn the

programme selector knob to the "Drain" programme

and press the "Start/Pause" button.

"Variable spin" button

• Every programme has a predefined spin speed.

• Press the button to set another spin speed.

• If spin speed "0" is selected, the final spinning is

cancelled but intermediate spin peaks remain

during rinse. The water is drained out only.

START DELAY

The "Start Delay" allows to run the machine at the

consumer's convenience, for example at night when

electricity is cheaper. Do not use liquid detergent

when activating the "Start Delay".

• Select programme, temperature and options.

• Press the "Start Delay" button to select the delay

time by 1 to 23 hours;

• Press the "Start/Pause" button.

The indication light over the "Start Delay"

button flashes and the countdown of the delay

time begins. The dot between hours and

minutes of the delay time indicated flashes.

• The time delay indication disappears when the

programme starts and it is replaced by the

remaining programme time.

• Once having pressed the "Start/Pause" button,

the number of hours preselected can be reduced

by pressing and holding the "Start Delay"

button. From 1 hour on, the delay time can also

be reduced in steps of 10 minutes.

To cancel the "Start Delay"

..before you press the "Start/Pause" button:

• Turn the programme selector to another

position or press the "Reset" button.

..after having pressed the "Start/Pause" button:

• Press the "Reset" button for at least 3 seconds - the

start delay time disappears from the time display.

PROGRAMME START

Open the tap and press the "Start/Pause" button. The

indication lamp next to the "Start/Pause" button lights

up. The programme sequence indicator shows the

current programme phase, running from left to right

through Wash, Rinse, Spin/Drain.

The display shows the remaining programme time.

Due to variations in load and temperature of inlet

water, the remaining time is newly calculated in certain

programme phases. If this is the case, an animation

appears on the time display.

"DOOR OPEN" INDICATION

Before starting and after end of a programme, the

lamp lights to show that the lid can be opened. As

long as a wash programme is running, the lid

remains locked and must on no account be forced

open. In case you have an urgent need to open it

during a running programme, refer to "Cancel

(Reset) a running programme before the end".

RED INDICATIONS

"Service"

Lighting up of the "Service" indication can be caused by

a fault in an electrical component. Refer to the

"Troubleshooting Guide" in your Instructions for Use; if

the fault persists, contact our After Sales Service.

"Water tap closed"

The appliance has no or insufficient water supply.

Open the water tap; if the indication still lights up,

refer to the "Troubleshooting Guide" in the

Instructions for Use.

"Clean filter"

Waste water is not pumped out. Check whether the

drain hose is kinked or the filter must be cleaned; in

the latter case refer to the Instructions for Use

("Removing the Filter").

PROGRAMME END

• All the lights of the programme sequence

indicator are off, and the "Door open"

indication lights up.

1. Turn the programme selector to the "Off/O" position.

2. Close the water tap.

3. Open lid and drum and unload the machine.

4. Leave the lid open to allow the inside of the

machine to dry.

CHANGE PROGRAMME AND/OR OPTIONS

AFTER PROGRAMME START

1. Press the "Start/Pause" button to pause the

programme. The light flashes.

2. Select the new programme, temperature, any

options and another spin speed if you want.

3. Press the "Start/Pause" button again. The new

programme continues at the same position

where the previous programme was interrupted.

Do not add detergent for this programme.

CANCEL (RESET) A RUNNING

PROGRAMME BEFORE THE END

The "Reset" button cancels a programme before

the end.

• Press the "Reset" button for at least 3

seconds. Any existing water is drained out

before the lid can be opened.

Whirlpool is a registered trademark of Whirlpool USA

5019 312 10588

1
2