Whirlpool AWO 3751 Panduan Cepat - Halaman 2
Jelajahi secara online atau unduh pdf Panduan Cepat untuk Mesin cuci Whirlpool AWO 3751. Whirlpool AWO 3751 3 halaman.
Halaman Cetak
30105698GB.fm Page 2 Tuesday, January 25, 2005 9:52 AM
CONSUMPTION DATA
Temperature
Programme
(°C)
Cotton
95
Cotton
60
Cotton
40
Synthetics
60
Synthetics
40
Daily
40
Quick wash
30
Delicates
40
Wool
30
Handwash
30
Prewash cycle might increase programme duration. Consumption values were measured in normalized conditions in compliance
with Standard IEC 60 456. Consumption data in the home may vary with respect to the values in the table in relation to the
water supply pressure and temperature, the load and the type of wash.
* The remaining time indicator can similarly deviate from the values in the table, because it takes into account the household
conditions applicable at that time.
** To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the
water out.
ADD DETERGENTS, CLOSE THE DOOR
AND SELECT THE PROGRAMME
Add the detergent as described in the programme
table or in the chapter "Detergents and Additives"
in the booklet.
1. Turn the programme selector knob to the
desired programme and temperature.
2. The remaining time display shows the duration
of the chosen programme (in hours and
minutes) and after taking some seconds for
calculating, the indication of the "Start/Pause"
button is flashing.
3. The programme sequence and the predefined
spin speed indication corresponding to the
selected programme lights up.
SELECT ANY DESIRED OPTION
Selecting any option the indication lights up.
When the combination of programme, additional
options and temperature is not possible, the
indication lights switch off automatically. Unsuitable
combinations of options are deselected
automatically.
Black process 45.0° 100.0 LPI
Load
Water
Energy
Approx.
Programme
Duration
(kg)
(l)
(kWh)
(hours : minutes)*
5.5
54**
1.90
2:00
5.5
49
1.04
2:20
5.0
44
0.60
2:05
2.5
55
0.80
1:30
2.5
55
0.60
1:20
3.0
45
0.50
1:00
3.0
37
0.40
0:30
1.5
60
0.60
0:45
1.0
60
0.30
0:40
1.0
45
0.30
0:40
"Easy Ironing" button
• Can be used together with "Cotton",
"Synthetics" and "Daily" programmes to make
ironing easier.
• Increases the water quantity and the clothes are
spun very soft.
"Eco" button
• The duration of the wash is extended and the
temperature reduced to save up to 40% of
energy but maintaining good washing results.
"Prewash" button
• Only for heavily soiled loads (for example sand,
granular dirt) sensible. The cycle time increases
approximately 15 min.
"Intensive Rinse" button
• More water and a longer time in rinse cycle is
added.
• This option is particularly suitable for areas with
very soft water, washing baby linen and helps
people with allergies.
"Rinse Hold" button
• The laundry remains in the last rinse water
without progressing to the final spin cycle to
avoid creasing and prevent colours from
changing.
• This option is particularly recommended for the
programme "Synthetics", "Daily" and
"Delicates".
• This function is particularly useful if you want to
postpone spinning to a later time, or if you want
to drain only.
Note: The programme stops to "Rinse Hold" at
the time the "Rinse Hold" light in the programme
sequence indication is on.
Terminate the "Rinse Hold" option:
• Press the "Rinse Hold" button again; the
programme will terminate automatically with the
final spin cycle for the present wash programme.
• If you do not wish to spin the clothes, turn the
programme selector knob counterclockwise to
the "Drain" programme and press the
"Start/Pause" button again when the indication
next to it is flashing.
"Spin Speed" button
• Every programme has an automatic predefined
maximum spin speed.
• Press the button to set another spin speed.
• If the spin speed "0" is selected, the final spinning
is cancelled but intermediate spin peaks remain
during rinse. The water is drained out only.
PROGRAMME START
Open the tap and press the "Start/Pause" button.
The indication next to the "Start/Pause" button
lights up. The indications show the sequence
reached in the programme. After starting the
programme, the sequence indication runs from left
to right through Wash, Rinse, Spin.
When the sequence of the programme is finished
the corresponding indication goes out.
RED INDICATIONS
"Water Tap Closed"
The appliance has no or insufficient water supply.
Open the water tap; if the indication still lights up,
refer to the "Troubleshooting Guide" in the
Instructions for Use.
"Clean Pump"
Waste water is not pumped out. Check whether the
drain hose is kinked or the filter must be cleaned; in
the latter case refer to the Instructions for Use
("Removing the Filter").
"Door Locked"
As long as a washing programme is running, the
lamp lights up to show that the door cannot be
opened. When the indication goes off, the door can
be opened again.
PROGRAMME END
• The remaining time is on "0:00" and all the lights
of the programme sequence indication are off.
"
/0"
1. Turn the programme selector to the
Off
position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry out.
CHANGE THE PROGRAMME, OPTIONS
AFTER PROGRAMME START
1. Press the "Start/Pause" button to pause the
programme. The light flashes.
2. Select the new programme (with temperature),
any options and another spin speed if you want.
3. Press the "Start/Pause" button again. The new
programme continues at the same position
where the previous programme was interrupted.
Do not add detergent for this programme.
CANCEL (RESET) A RUNNING
PROGRAMME BEFORE THE END
The "Reset" button cancels a programme before
the end.
• Press the "Reset" button for at least 3
seconds. Any existing water is drained out
before the door can be opened.
Whirlpool is a registered trademark of Whirlpool USA
5019 301 05698