Whirlpool AWO/D 3080 Bagan Program - Halaman 2
Jelajahi secara online atau unduh pdf Bagan Program untuk Mesin cuci Whirlpool AWO/D 3080. Whirlpool AWO/D 3080 2 halaman.
Halaman Cetak
CONSUMPTION DATA
Temperature
Programme
(°C)
Cotton
95
Cotton**
60
Cotton
40
Synthetics
60
Synthetics
40
Delicates
30
Quick wash
30
Wool
40
Handwash
40
Handwash
30
Consumption values were measured in normalized conditions in compliance with standard IEC/EN 60 456. Consumption data in the
home may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type
of wash.
*
To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water
out.
** Reference Programme for Energy Label.
ADD DETERGENTS, CLOSE THE DOOR AND
SELECT THE PROGRAMME
Add detergents as indicated on the front page and as
described in your Instructions for Use. Close the door
and turn the programme selector to the desired
programme and temperature. The indication lamp next
to the "Start/Pause" button flashes.
SELECT ANY DESIRED OPTION
Push the button(s) of any option(s) desired - the
respective indication lamp lights up.
When the combination of programme and additional
option(s) is not possible, the indication lights switch off
automatically. Unsuitable combinations of options are
deselected automatically.
"No spin" button
•
Especially for delicate garments to avoid wear and
tear caused by the spin.
Note: with the "Cotton" and "Synthetics"
programmes, a short spin cycle is provided in any
case, even if the "No spin" option has been selected,
in order to optimize rinsing results.
Downloaded From WashingMachine-Manual.com Manuals
Load
Water
Energy
Approx. Programme
Duration
(kg)
(l)
(kWh)
(hours : minutes)
5.0
49*
1.90
5.0
44
0.85
5.0
44
0.60
2.5
50*
0.70
2.5
45
0.55
1.5
50
0.50
3.0
40
0.40
1.0
55
0.60
1.0
45
0.60
1.0
45
0.50
"Rinse hold" button
•
The laundry remains in the last rinse water without
progressing to the final spin cycle to avoid creasing
and prevent colours from changing.
•
This option is particularly recommended for the
programmes "Synthetics" and "Delicates".
•
This function is particularly useful if you want to
postpone spinning to a later time, or if you want to
drain only.
Note: The programme stops to "Rinse hold" at the
time the "Anticrease" light in the programme
sequence indicator is on. The indication lamp next
to the "Start/Pause" button flashes.
•
If you select "Rinse hold" do not leave items to soak
for too long.
Terminate the "Rinse hold" option:
•
Press the "Start/Pause" button; the programme
will terminate automatically with the final spin cycle
for the present wash programme.
•
If you do not wish to spin the clothes, turn the
programme selector knob to the "Drain"
programme and press the "Start/Pause" button.
PROGRAMME START
Open the tap and press the "Start/Pause" button.
The indication lamp next to the "Start/Pause" button
lights up. The programme sequence indicator shows
the current programme phase, running from left to right
2:00
through Wash, Rinse, Spin/Drain.
2:20
When the programme phrase is finised, the
corresponding indication goes out.
2:00
1:30
"DOOR OPEN" INDICATION
1:15
Before starting and after end of a programme, the lamp
0:45
lights to show the the door can be opened. As long
0:30
as a wash programme is running, the door remains
locked and must on no account be forced open.
0:45
In case you have an urgent need to open it during a
0:40
running programme, refer to "Cancel (Reset) a running
0:40
programme before the end".
RED INDICATIONS
"Service"
Lighting up of the "Service" indication can be caused
by a fault in an electrical component. Refer to the
"Troubleshooting Guide" in your "Instructions for Use";
if the fault persists, contact our After Sales Service.
"Water tap closed"
The appliance has no or insufficient water supply. Open
the water tap: if the indications still lights up, refer to the
"Troubleshooting Guide" in the Instructions for Use.
"Clean filter"
Waste water is not pumped out. Check whether the
drain hose is kinked or the filter must be cleaned: in the
latter case refer to the Instructions for Use ("Removing
the Filter").
PROGRAMME END
•
All the lights of the programme sequence indicator
are off, and the "Door open" indication lights up.
1. Turn the programme selector to the "Off/O"
position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
1. Press the "Start/Pause" button to pause the
programme. The light flashes.
2. Select the new programme (with temperature), any
options and another spin speed if you want.
3. Press the "Start/Pause" button again. The new
programme continues at the same position where
the previous programme was interrupted. Do not
add detergent for this programme.
CANCEL (RESET) A RUNNING PROGRAMME
BEFORE THE END
The "Reset" button cancels a programme before the
end.
•
Press the "Reset" button for at least 3 seconds.
Any existing water is drained out before the door
can be opened.
Whirlpool is a registered trademark of Whirlpool USA.
5019 301 10401