Whirlpool WASHER Panduan Petunjuk Instalasi - Halaman 4

Jelajahi secara online atau unduh pdf Panduan Petunjuk Instalasi untuk Mesin cuci Whirlpool WASHER. Whirlpool WASHER 20 halaman. Washing machine
Juga untuk Whirlpool WASHER: Panduan Petunjuk Instalasi (16 halaman), Panduan Petunjuk Instalasi (27 halaman), Petunjuk Pengguna (8 halaman), Petunjuk Pengguna (20 halaman), Petunjuk Pengguna (24 halaman), Petunjuk Pengguna (8 halaman), Petunjuk Pengguna (15 halaman), Panduan Penggunaan & Perawatan (40 halaman), Panduan Petunjuk Instalasi (16 halaman), Petunjuk Pengguna (8 halaman), Bagan Program (2 halaman), Petunjuk Instalasi (5 halaman), Panduan Petunjuk Instalasi (8 halaman)

Halaman Cetak
Whirlpool WASHER Panduan Petunjuk Instalasi

DRAIN SYSTEM

Drain system can be installed using a floor drain, wall standpipe,
floor standpipe, or laundry tub. Select method you need.
Floor standpipe drain system
4
1
/
"
2
(114 mm)
Minimum diameter for a standpipe drain: 2" (51 mm). Minimum
carry-away capacity: 17 gal. (64 L) per minute. Top of standpipe
must be at least 39" (990 mm) high; install no higher than 96"
(2.44 m) from bottom of washer. If you must install higher than
96" (2.44 m), you will need a sump pump system.
Wall standpipe drain system
4
1
/
"
2
(114 mm)
See requirements for floor standpipe drain system.
Floor drain system
Floor drain system requires a Siphon Break Kit (Part Number
285834), 2 Connector Kits (Part Number 285835), and an
Extension Drain Hose (Part Number 285863) that may be
purchased separately. To order, please see toll-free phone
numbers in your "Use and Care Guide." Minimum siphon break:
28" (710 mm) from bottom of washer. (Additional hoses may
be needed.)
Laundry tub drain system
4
1
/
"
2
(114 mm)
Minimum capacity: 20 gal. (76 L). Top of laundry tub must be at
least 39" (990 mm) above floor; install no higher than 96" (2.44 m)
from bottom of washer.
IMPORTANT: To avoid siphoning, no more than 4 ½" (114 mm)
of drain hose should be inside standpipe or below the top of
wash tub. Secure drain hose with cable tie.
4
39"
(990 mm)
39"
30"
(990 mm)
(762 mm)

ELECTRICAL REQUIREMENTS

A 120 volt, 60 Hz., AC only, 15- or 20-amp, fused electrical
■
supply is required. A time-delay fuse or circuit breaker on
a separate circuit serving only this washer is recommended.
This washer is equipped with a power supply cord having
■
a 3-prong grounding plug.
To minimize possible shock hazard, the cord must be
■
plugged into a mating, 3-prong, grounding-type outlet,
grounded in accordance with local codes and ordinances.
If a mating outlet is not available, it is the personal
responsibility and obligation of the customer to have the
properly grounded outlet installed by a qualified electrician.
If codes permit and a separate ground wire is used, it is
■
recommended that a qualified electrician determine that
the ground path is adequate.
Do not ground to a gas pipe.
■
Check with a qualified electrician if you are not sure
■
the washer is properly grounded.
Do not have a fuse in the neutral or ground circuit.
■