Whirlpool GSC25C6EYW Petunjuk Pengguna - Halaman 4

Jelajahi secara online atau unduh pdf Petunjuk Pengguna untuk Kulkas Whirlpool GSC25C6EYW. Whirlpool GSC25C6EYW 44 halaman. Sxs xxl refrigerators water filter housing/door misaligned
Juga untuk Whirlpool GSC25C6EYW: Dimensi Produk (1 halaman), Manual Energi (2 halaman), Penunjuk Layanan Teknis (4 halaman)

Halaman Cetak

Replacing the Produce Preserver (on some models)

The disposable pouches should be replaced every 6 months,

when the status indicator has completely changed from white to

red.

To order replacements, see "Accessories."

1. Remove the old pouches from the Produce Preserver housing.

2. Remove the old status indicator.

3. Install the new pouches and status indicator using the

instructions in the previous sections.

Using the Controls

The refrigerator and freezer controls are located on the dispenser

panel.

IMPORTANT: The display screen on the dispenser control panel

will turn off automatically and enter "sleep" mode when the

control buttons and dispenser pads have not been used for

2 minutes or more. While in "sleep" mode, the first press of a

control button will only reactivate the display screen, without

changing any settings. After reactivation, changes to any settings

can then be made. If no changes are made within 2 minutes, the

display will re-enter "sleep" mode.

Touch any control button on the dispenser panel to activate

the display screen. The home screen will appear as shown.

Adjusting the Controls

For your convenience, your refrigerator and freezer controls are

preset at the factory. When you first install your refrigerator, make

sure that the controls are still set to the "mid-settings." The factory

recommended set points are 37°F (3°C) for the refrigerator and

0°F (-18°C) for the freezer.

IMPORTANT:

Wait 24 hours before you put food into the refrigerator. If you

add food before the refrigerator has cooled completely, your

food may spoil.

NOTE: Adjusting the set points to a colder than

recommended setting will not cool the compartments any

faster.

If the temperature is too warm or too cold in the refrigerator or

freezer, first check the air vents to be sure they are not

blocked before adjusting the controls.

The preset settings should be correct for normal household

usage. The controls are set correctly when milk or juice is as

cold as you like and when ice cream is firm.

Wait at least 24 hours between adjustments. Recheck the

temperatures before other adjustments are made.

To view and adjust the set points, press and hold the TEMP

button for 3 seconds. When adjust mode is activated, adjusting

information will appear on the display screen.

NOTE: To view Celsius temperatures, press the LIGHT button

when adjust mode is activated. To return the display setting to

Fahrenheit, press LIGHT again.

When adjust mode is activated, the display screen shows the

refrigerator set point and "FRIDGE" appears.

Press LOCK to raise the set point, or press FAST ICE to lower

the set point.

When you have finished viewing (and adjusting if desired) the

refrigerator set point, press TEMP to change the display to

show the freezer set point. When the zone has been changed,

"FREEZER" appears on the display screen.

Press LOCK to raise the set point, or press FAST ICE to lower

the set point.

When you have finished viewing (and adjusting if desired) both

the refrigerator and freezer set points, press FILTER to save

the settings.

NOTE: To exit without saving changes, press ICE TYPE at any

time while in adjust mode, or allow about 60 seconds of

inactivity and adjust mode will turn off automatically.

When adjusting temperature set points, use the following chart as

a guide.

CONDITION:

REFRIGERATOR too cold

REFRIGERATOR too warm

FREEZER too cold

FREEZER too warm /

Too little ice

The set point range for the refrigerator is 33°F to 45°F (0°C to

7°C). The set point range for the freezer is -5°F to 5°F (-21°C to

-15°C).

Cooling On/Off

Your refrigerator and freezer will not cool when cooling is

turned off.

To turn cooling off, press and hold the LOCK and FILTER

buttons at the same time for 3 seconds.

IMPORTANT: To avoid unintentionally locking the dispenser

or changing other settings, be sure to press both buttons at

exactly the same time.

When cooling is off, "COOLING OFF" will appear on the

display screen.

Press and hold LOCK and FILTER for 3 seconds again to turn

cooling back on.

TEMPERATURE

ADJUSTMENT:

REFRIGERATOR Setting

1° higher

REFRIGERATOR Setting

1° lower

FREEZER Setting

1° higher

FREEZER Setting

1° lower