Ariston TCL73XS Buklet Perawatan, Penggunaan, dan Pemasangan - Halaman 9
Jelajahi secara online atau unduh pdf Buklet Perawatan, Penggunaan, dan Pemasangan untuk Pengering Ariston TCL73XS. Ariston TCL73XS 44 halaman.
Juga untuk Ariston TCL73XS: Panduan Penggunaan dan Instalasi (44 halaman)
Halaman Cetak
Start and Programs
The Controls
PROGRAMS knob
! Warning, if after pressing the Start/Pause button
the programs knob position has changed, the new
position will NOT change the program selected.
To change the program: Press the Start/Pause button
to pause the program - the light flashes amber to indicate
the program is paused. Select the new program and
any options required - the light will flash green. Press
the Start/Pause button
and the new program will
start.
OPTION buttons / lights
These buttons are used to customize the selected
program to your requirements. Not all options are
available for all programs (see Start and Programs).
If an option is not available and you press the button,
the buzzer (alert) will beep three times. If the option is
available there will be one beep and the option light
next to the button lights to confirm the selection.
Progress (Drying, Cool Tumble, End) /
Delay (3hr 6hr 9hr) Lights
When the light next to the delay button is on, these lights
flash to indicate the delay time is selected. During other
programs they indicate the progress of the dryer, each
one comes on as the corresponding phase starts.
Delay Timer
The start of some programs (see Start and Programs)
can be delayed for up to 9 hours in 3hr steps.
Ensure that the water container is emptied before
setting a delayed start.
When a delayed start is in progress the light next to the
delay button will be on and the selected delay period
light will flash (after the Start/Pause button has been
pressed).
To set a delayed start, press the Delay Timer button,
and the light next to the button will come on together
with the 3hr delay light. Pressing the button again will
advance the delay setting to 6hr, the 3hr light goes
out and the 6hr light is on. Each time you press the
button the delay setting advances 3 hours, as indicated
by the corresponding light. If the 9hr light is on,
pressing the button again will cancel the delay.
You can also cancel the delay by holding in the On/Off
button.
Pre Care
When a delayed start and this option have been
selected, the clothes are tumbled occasionally during
the delayed period to help prevent creases developing.
High Heat
Available for Timed Drying programs. Press this
button and a high heat setting is selected and the light
alongside the button comes on.
Timed programs have a default of low heat, if the light
alongside the button is on then pressing the button
selects a low heat setting and the light goes out.
Post Care
When available and selected, the clothes are
occasionally tumbled after the end of the drying and
cool tumble cycles, to help prevent creases
developing should you not be available to remove the
load immediately the program is complete.
The 'End light is on during this phase.
Door Opening
Opening the door (or pressing the Start/Pause button
during a program will stop the dryer and have the
following effects:
The Start/Pause light flashes amber.
During a delay phase the delay will continue to
count down. The Start/Pause button must be
pressed to resume the delay program.
One of the delay lights will flash to show the
current delay setting.
The Start/Pause button must be pressed to
resume the program. The progress lights will
change to show the current status and the
Start/Pause light will stop flashing and turn green.
During the post care phase of a drying program
the program will finish. Pressing the Start/Pause
button will re-start a new program at the
beginning.
Changing the Programs knob will select a new
program and the Start/Pause light will flash
green. You can use this to select the Cool Tumble
program
to cool the clothes, if you find them dry
enough. Press the Start/Pause button to begin a
new program.
Note
If you have a power outage, switch off the power or
remove the plug, press the Start/Pause button and the
program will resume.
EN
)
9