Whirlpool 29" Wide Models Panduan Petunjuk Instalasi - Halaman 6

Jelajahi secara online atau unduh pdf Panduan Petunjuk Instalasi untuk Pengering Whirlpool 29" Wide Models. Whirlpool 29" Wide Models 20 halaman. Dryer
Juga untuk Whirlpool 29" Wide Models: Panduan Petunjuk Instalasi (48 halaman), Panduan Petunjuk Instalasi (22 halaman)

Halaman Cetak

Minimum Required Spacing

14"* max.

(356 mm)

(140 mm)

1"*

(25 mm)

A. Recessed area

B. Side view - closet or confined area

C. Closet door with vents

*Required spacing

Mobile home - Additional installation

requirements

This dryer is suitable for mobile home installations. The

installation must conform to the Manufactured Home

Construction and Safety Standard, Title 24 CFR, Part 3280

(formerly the Federal Standard for Mobile Home Construction

and Safety, Title 24, HUD Part 280).

Metal exhaust system hardware, which is available for

■

purchase from your dealer.

Special provisions must be made in mobile homes to

■

introduce outside air into the dryer. The opening (such

as a nearby window) should be at least twice as large

as the dryer exhaust opening.

Electrical Requirements

It is your responsibility:

To contact a qualified electrical installer.

■

To be sure that the electrical connection is adequate and in

■

conformance with the National Electrical Code, ANSI/NFPA

70-latest edition and all local codes and ordinances.

The National Electrical Code requires a 4-wire power supply

connection for homes built after 1996, dryer circuits involved

in remodeling after 1996, and all mobile home installations.

A copy of the above code standards can be obtained from:

National Fire Protection Association, One Batterymarch Park,

Quincy, MA 02269.

To supply the required 3 or 4 wire, single phase, 120/240 volt,

■

60 Hz, AC only electrical supply (or 3 or 4 wire, 120/208 volt

electrical supply, if specified on the serial/rating plate) on a

separate 30-amp circuit, fused on both sides of the line. A

time-delay fuse or circuit breaker is recommended. Connect

to an individual branch circuit. Do not have a fuse in the

neutral or grounding circuit.

3"*

(76 mm)

48 in.

(310 cm

18"*

(457 mm)

24 in.

(155 cm

1"*

(25 mm)

3"*

(76 mm)

Do not use an extension cord.

■

If codes permit and a separate ground wire is used, it is

■

recommended that a qualified electrician determine that

the ground path is adequate.

Electrical Connection

To properly install your dryer, you must determine the type of

electrical connection you will be using and follow the instructions

provided for it here.

If local codes do not permit the connection of a neutral ground

)

■

wire to the neutral wire, see "Optional 3-wire connection"

section.

This dryer is manufactured ready to install with a 3-wire

■

electrical supply connection. The neutral ground wire is

permanently connected to the neutral conductor (white wire)

within the dryer. If the dryer is installed with a 4-wire electrical

supply connection, the neutral ground wire must be removed

from the external ground connector screw (green screw), and

)

secured under the neutral terminal (center or white wire) of the

terminal block. When the neutral ground wire is secured under

the neutral terminal (center or white wire) of the terminal block,

the dryer cabinet is isolated from the neutral conductor.

A 4-wire power supply connection must be used when the

■

dryer is installed in a location where grounding through the

neutral conductor is prohibited. Grounding through the neutral

is prohibited for (1) new branch-circuit installations, (2) mobile

homes, (3) recreational vehicles, and (4) areas where local

codes prohibit grounding through the neutral conductors.

If using a power supply cord:

Use a UL listed power supply cord kit marked for use with

clothes dryers. The kit should contain:

A UL listed 30-amp power supply cord, rated 120/240 volt

■

minimum. The cord should be type SRD or SRDT and be

at least 4 ft. (1.22 m) long. The wires that connect to the

dryer must end in ring terminals or spade terminals with

upturned ends.

A UL listed strain relief.

■

If your outlet looks like this

4-wire receptacle

(14-30R)

If your outlet looks like this:

3-wire receptacle

(10-30R)

If connecting by direct wire:

Power supply cable must match power supply (4-wire or 3-wire)

and be:

Flexible armored cable or nonmetallic sheathed copper cable

■

(with ground wire), covered with flexible metallic conduit. All

current-carrying wires must be insulated.

10-gauge solid copper wire (do not use aluminum).

■

At least 5 ft. (1.52 m) long.

■

Then choose a 4-wire power supply cord with

ring or spade terminals and UL listed strain

relief. The 4-wire power supply cord, at least

4 ft. (1.22 m) long, must have 4 10-gauge solid

copper wires and match a 4-wire receptacle of

NEMA Type 14-30 R. The ground wire (ground

conductor) may be either green or bare. The

neutral conductor must be identified by a white

cover.

Then choose a 3-wire power supply cord with

ring or spade terminals and UL listed strain

relief. The 3-wire power supply cord, at least

4 ft. (1.22 m) long, must have 3 10-gauge solid

copper wires and match a 3-wire receptacle of

NEMA Type 10-30R.