Whirlpool YCEP2760KQ0 Panduan Petunjuk Instalasi - Halaman 4

Jelajahi secara online atau unduh pdf Panduan Petunjuk Instalasi untuk Pengering Whirlpool YCEP2760KQ0. Whirlpool YCEP2760KQ0 27 halaman. Commercial dryer gas or electric

Halaman Cetak

A main exhaust vent can be used for

exhausting

a group

of dryers, Main

exhaust vent should

be sized to

remove 200 CFM of air per dryer,

Large-capacity

lint screens of proper

design

may be used in the main

exhaust vent if checked

and cleaned

frequently,

The room where the dryers

are located

should

have make-up

air

equal

to or greater

than the CFM of

all the dryers in the room,

alrnow _

ma[ncole_ot'vent

-4_

Back-draft

Damper Kits, Part No,

339191 B, are available

from your

Whirlpool

dealer

and should

installed

in each dryer's exhaust vent

to prevent

exhausted

air from

returning

into the dryers and to keep

the exhaust in balance

within the

main exhaust vent, Unobstructed

air

openings

are required,

Each exhaust vent should enter the

main vent at an angle

pointing

in the

direction

of the airflow, Vents entering

from the opposite

side should

staggered

to reduce

the exhausted

air from interfering

with the other

vents,

The maximum

angle of each vent

entering

the main vent should

be no

more than 30 °,

Keep air openings free of dry

cleaning

fluid fumes. Fumes create

acids which, when drawn through the

dryer heating units, can damage

dryers and loads being dried.

A clean-out

cover should be located

on the main exhaust vent for

periodically

cleaning

of the exhaust

system,

An exhaust hood should cap the

outside end of the main vent to

prevent

exhausted

air from returning

to the dryers, If an exhaust hood

cannot

be used, the outside end of

the main duct should

have a sweep

elbow

directed

downward,

If the

main vent travels vertically

through

the roof, rather than through

the wall,

install 180 ° sweep

elbow on the end

of vent at least 2 feet (61 cm) above

the highest part of the building,

The

opening

wall or roof shall have a

diameter

1/2 inch (1,3 cm) larger than

the exhaust vent diameter,

The

exhaust vent should be centered

the opening,

exhaull

hood or

-_(

wall

U.°°T,a-

main exhaull

vent

wall

180 °

_Neop

2 ft. (61 cm)

I--_

_/elbow

min. above

highest point of

building

main collector

vent

Do Not install screening or cap over

end of vent,

Gas requirements

Explosion Hazard

Use a new AGA or CSA

approved gas supply line.

Install a shut-off valve.

Securely tighten all gas

connections.

If connected to LP, have a

qualified person make sure gas

pressure does not exceed t3"

(33 cm) water column. Examples

of a qualified person include

licensed heating personnel,

authorized gas company

personnel, and authorized

service personnel.

Failure to do so can result in

death, explosion, or fire.

OBSERVE ALLGOVERNING CODES

AND ORDINANCES.

This installation

must conform

with local codes,

or in absence

local codes

with the National

Fuel

Gas Code

ANSI Z223,1/NFPA 54 or the

CAN/CGA

- B149 installation

codes,

n The design of this dryer has

been certified

by the CSA

International

for use at altitudes

up to

10,000 feet (3048 m) above

sea level

at the B,T,U, rating indicated

on the

model/serial

plate,

Burner input

adjustments

are not required

when

the dryer is operated

up to this

elevation,

When installed above

10,000 feet

(3048 m), a four percent

(4%)

reduction

of the burner B,T,U, rating

shown on the model/serial

plate

required

for each

1,000 foot (305 m)

increase

in elevation,

For assistance

when converting

to other gas types

and/or

installing

above

10,000 feet

(3048 m) elevation,

contact

your

local service company,

Page 4