Whirlpool YGEW9250PW Panduan Penggunaan & Perawatan - Halaman 7

Jelajahi secara online atau unduh pdf Panduan Penggunaan & Perawatan untuk Pengering Whirlpool YGEW9250PW. Whirlpool YGEW9250PW 40 halaman. Electronic electric dryer

Halaman Cetak

If using a replacement power supply cord, it is recommended

that you use Power Supply Cord Replacement Part Number

9831317. For further information, please reference the service

numbers located in the "Assistance

or Service" section of this

manual.

GROUNDING INSTRUCTIONS

For a grounded, cord-connected

dryer:

This dryer must be grounded. In the event of malfunction

or breakdown, grounding will reduce the risk of electric shock

by providing a path of least resistance for eiectric current. This

dryer is equipped with a cord having an equipment-grounding

conductor and a grounding plug. The piug must be plugged

into an appropriate outlet that is properly installed and

grounded in accordance with all local codes and ordinances.

WARNING

: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or service representative or

personnel if you are in doubt as to whether the dryer is

properly grounded. Do not modify the plug provided with the

dryer: if it will not fit the outlet, have a proper outlet installed

by a qualified electrician.

SAVE THESE INSTRUCTIONS

Fire Hazard

Use a heavy metaB vent.

Do not use a pmastic vent.

Do not use a metal foil vent.

Failure to follow

these instructions

can result in death

or fire.

WARNING;

To reduce the risk of fire, this dryer MUST BE

EXHAUSTED OUTDOORS.

4" (10.2 cm) heavy metal exhaust vent and clamps must be used.

DURASAFE

vent products are recommended.

DURASAFE

vent products can be purchased from your dealer

or by calling Whirlpool Parts and Accessories.

For more

information, see the "Assistance

or Service" section of this

manual.

•

The dryer exhaust must not be connected

into any gas vent,

chimney, wall, ceiling, or a concealed

space of a building.

•

Do not use an exhaust hood with a magnetic latch.

•

Do not install flexible metal vent in enclosed walls, ceilings or

floors.

Use clamps to seal all joints. Exhaust vent must not be

connected or secured with screws or other fastening devices

which extend into the interior of the duct. Do not use duct

tape.

IMPORTANT: Observe all governing codes and ordinances.

_mproper venting

can cause moisture

and mintto co_mect

indoors,

which

may resumt in:

[]

Moisture damage to woodwork,

furniture, paint,

wallpaper, carpets, etc.

[]

Housecleaning

problems and health problems.

Use a heavy metal vent. Do not use plastic or metal foil vent.

Rigid metal vent is recommended

to prevent crushing and

kinking.

Flexible metal vent must be fully extended and supported

when

the dryer is in its final position. Remove excess flexible metal vent

to avoid sagging and kinking that can result in reduced airflow

and poor performance.

An exhaust hood should cap the vent to prevent rodents and

insects from entering the home.

Exhaust hood must be at least 12" (30.5 cm) from the ground or

any object that is in the path of the exhaust (such as flowers,

rocks or bushes, etc.).

If using an existing vent system, clean lint from the entire length

of the system and make sure exhaust hood is not plugged with

lint. Replace any plastic or metal foil vent with rigid metal or

flexible metal vent.

Typical exhaust

installations

Typical installations vent the dryer from the rear of the dryer.

Other installations are possible.

A. Dryer

B. Elbow

C. Wall

D. Exhaust hood

E. Clamps

E Rigid metal or flexible metal vent

G. Vent length necessary to connect elbows

H. Exhaust outlet