Whirlpool RH4836XLT1 Panduan Penggunaan & Perawatan - Halaman 6
Jelajahi secara online atau unduh pdf Panduan Penggunaan & Perawatan untuk Kap Ventilasi Whirlpool RH4836XLT1. Whirlpool RH4836XLT1 10 halaman. 30/36" (76.2/91.4 cm) convertible range hood installation instructions
Juga untuk Whirlpool RH4836XLT1: Daftar Bagian (1 halaman)
Halaman Cetak
keyhole
s_ot
front
of hood
® Lift the range hood up under
cabinet and determine
finaU
position.
Mark on the underside
of cabinet the Uocadon of the four
keyhob
mounting
sbts. Set
range hood aside on a protected
surface.
drill
pilot
hole
® Use 1/8" (or 3 ram) ddH bit
and drill 4 pibt
hobs
as shown.
1/4"
(6.4 rnm)
I
O.
Remove the 4 hood
mounting screws from the parts bag
and install in pilot hoUes. Leave
screw' heads away from shim
strips about 1/4" (6.4 cm)
1[]
if using direct wiring, make
sure power is disconnected, and pull
about 12" (30 cm) of wire through
wail or cabinet and into opening.
installations,
one end of the vent
connector
may need to be
trimmed
to clear the electrical
strain relief.
Make electrical
Electrical Shock Hazard
Disconnect
power before making
electrical connections.
Connect ground w{re to green
ground screw in terminal box.
Failure to do so can result in
death or electricaJ shock.
5®
Depress both sides of the
light lens until tabs disengage
from slots in hood and remove
lens.
Install two 40 watt (maximum)
type Aq5 appliance
bulbs.
Reinstall
light
lens. Depress
both
sides
of lens,
insert
tabs
into slots
and release.
6[]
For non-vented
installations:
Grasp tab at front
center of filter. Push toward
back
to release filter from spring clips
at front. Puil down then froward
to remove aluminum
mesh filter.
Install non-vented
filter
(purchased
separately)
by
inserting
into channel at back of
compartment.
Grasp tab and pull
forward
so that filter snaps under
spring dips at front.
To get the most
efficient
use from
your
new range
hood,
read the "Use
and
Care mnformation"
section.
Keep your Whirlpool
mnstaHation
instructions
and
Use and Care Guide
close
to range hood for easy
reference.
2[]
Lift range hood into final
position,
feeding
electrical
wire
through
wiring
opening.
Position
the
range hood so that the large end of
the keyhole
slots are over the
screws.Then
push the hood toward
the wail so that the screws are in the
neck of the slots.Tighten
mounting
screws to cabinet,
making
sure
mounting
screws are in narrow
neck
of slots. Make sure that damper
blade, if used, rotates
up and down
freely.
13m
Connect ventwork
to hood.
Seal joints with duct tape to make
the secure and air tight.
Note:
Damper/vent
connector
and
round
vent
plate
can be installed
up to 1/2" (12.7 ram)
on either
side of hood
center
if ventwork
is
off-center,
in extreme
off-center
green
groun¢
screw
14"[] Directwiring:
Connect the white and black wires
of the power supply cable to the
white and black leads in the hood
with twist-on
connectors.
Connect the power supply ground
wire to the green ground
screw'
inside the terminal
bex.
Use caulking
to seal wire opening.
Replace terminal
box cover.
Using a U.L.-listed power
supply cord-connection
kit
(U.S. only}:
FoHew Power Cord }(it instructiens for
connecting wi_ng.