Whirlpool UXT4030AY Petunjuk Pemasangan Dan Panduan Penggunaan & Perawatan - Halaman 14
Jelajahi secara online atau unduh pdf Petunjuk Pemasangan Dan Panduan Penggunaan & Perawatan untuk Kap Ventilasi Whirlpool UXT4030AY. Whirlpool UXT4030AY 36 halaman. 30" (76.2 cm) and 36" (91.4 cm) range hood
Juga untuk Whirlpool UXT4030AY: Petunjuk Pemasangan Dan Panduan Penggunaan Dan Perawatan (32 halaman), Petunjuk Pemasangan Dan Panduan Penggunaan & Perawatan (24 halaman)
Halaman Cetak
For non-vented
(recirculating)
installations:
The charcoal filter is not washable. It should last up to 6 months
with normal use.
1. Replace metal grease filter with a charcoal filter. For
information
on ordering, see the "Accessories"
section.
To replace filter:
1. Remove screw from the grease filter retainer.
2. Turn the grease filter retainer to release filter.
3. Reinstall the filter by placing the back edge in the channel at
rear of hood. Push filter into place, turn the filter retainer to
secure filter to range hood.
4. Replace screw in the grease filter retainer.
Metal Grease Filter (UXT52 Series Models)
Replacing the Incandescent Light Bulb (UXT20, UXT30,
UXT40 and UXT42 Series Models)
Turn off the range hood and allow the light bulb to cool.
1. Disconnect
power.
2. Squeeze the plastic lens cover and remove it from the hood.
B
A
For vented installations:
1. Remove screw from the grease filter retainer.
2. Turn the grease filter retainer to release filter.
A
C
A. Halogen lights
B. Grease filter handle
C. Grease filter
3. Wash metal filters as needed in dishwasher or hot detergent
solution.
4. Reinstall the filter by placing the back edge in the channel at
rear of hood. Push filter into place, turn the filter retainer to
secure filter to range hood.
5. Replace screw in the grease filter retainer.
6. Repeat steps 1-5 for the other filter.
For non-vented
(recirculating)
installations:
The charcoal filter is not washable. It should last up to 6 months
with normal use.
1. Replace metal grease filter with a charcoal filter. For
information
on ordering, see the "Accessories"
section.
To replace filter:
1. Remove screw from the grease filter retainer.
2. Turn the grease filter retainer to release filter.
3. Reinstall the filter by placing the back edge in the channel at
rear of hood. Push filter into place, turn the filter retainer to
secure filter to range hood.
4. Replace screw in the grease filter retainer.
5. Repeat steps 1-5 for the other filter.
A. Light bulb socket
B. Lens cover
3. Screw light bulb into socket.
4. Replace lens cover by squeezing cover and inserting tabs
into slots.
5. Reconnect power.
If new light does not operate, make sure the lamp is inserted
correctly before calling service.
Replacing
the Halogen
Lamp (UXT52 Series Models)
Turn off the range hood and allow the halogen lamp to cool. To
avoid damage or decreasing the life of the new bulb, do not
touch bulb with bare fingers. Replace bulb, using tissue or
wearing cotton gloves to handle bulb.
If new lamps do not operate, make sure the lamps are inserted
correctly before calling service.
1. Disconnect
power.
2. Push up on the lens and turn it counterclockwise.
3. Remove the bulb and replace it with a 120-volt, 50-watt
maximum halogen bulb with a GUIO base. Turn it clockwise
to lock it into place.
4. Repeat steps 2-3 for the other bulbs if needed.
5. Reconnect power.
14