FireScapes 702 Panduan Pemasangan dan Pengoperasian Pemilik Rumah - Halaman 2
Jelajahi secara online atau unduh pdf Panduan Pemasangan dan Pengoperasian Pemilik Rumah untuk Perapian Luar Ruangan FireScapes 702. FireScapes 702 5 halaman.
Halaman CetakIMPORTANT: Read all instructions and warnings
carefully before starting installation. Failure to
follow these instructions may result in a possible
fire hazard and will void the warranty.
WARNING: Improper installation, adjustment,
alteration, service or maintenance can cause injury
or property damage. Read the installation,
operating and maintenance instructions thoroughly
before installing or servicing this appliance.
WARNING: This appliance shall be used only
outdoors in a well-ventilated space and shall NOT
be used inside a building, garage or any other
enclosed area.
WARNING: This unit is NOT for use with solid
fuel.
NOTE: All new LP cylinders (and in many cases
used cylinders) may contain water, air or other
contaminants. It is essential that those be removed
before filling the cylinder and placing into service.
Water vapor present in the gas vapor may cause the
regulator to "freeze up" and cause an interruption to
the gas flow. This interruption will cause the unit to
shut down. To prevent this from occurring, it is
essential that a qualified individual ALWAYS
purge a new tank thoroughly before placing it into
service. It is recommended that cylinders that have
not been used for extended periods of time also be
purged before use.
The installation must conform with Local Codes or,
in the absence of local codes, with the National Fuel
Gas Code ANSI Z223.1 or CSA-B140.1 installation
code.
The appliance and its individual shut off valve must
be disconnected from the gas supply piping system
during any pressure testing or the system at test
pressure in excess of ½ psig (3.5kPa).
This appliance must be isolated from the gas supply
piping system by closing its individual manual shut
off valve during any pressure testing of the gas
supply piping system at test pressures equal to or
less than ½ psig (3kPa).
General Information
Always keep the appliance area clear and free from
combustible materials, gasoline and other
flammable vapors and liquids.
Children and adults should be alerted to the hazards
of high surface temperatures and should stay away to
avoid burns or clothing ignition.
Young children should be carefully supervised when
they are in the area of the appliance.
Never leave the unit unattended during operation.
Clothing or other flammable materials should not be
hung from the appliance, or placed on or near the
appliance.
Installation and repair should be done by a qualified
service person. The appliance should be inspected
before use and at least annually by a qualified service
person. More frequent cleaning may be required as
necessary. It is imperative the control compartment
burners and circulation air passageways of the
appliance be kept clean and free of debris.
Inspect the fuel supply connection (including the
hose for LP models) before each use of the appliance.
If it is evident there is excessive abrasion or wear, or
the hose is cut, it must be replaced prior to the
appliance being put into operation.
The pressure regulator and hose assembly supplied
with LP models must be used. Replacement pressure
regulators and hose assemblies must be those
specified in this manual.
The LP gas supply cylinder used with LP models
must be constructed and marked in accordance with
the specifications for LP gas cylinders of the U.S.
Department of Transportation (DOT) or the
specifications in the National Standard of Canada,
CAN/CSA B330, Cylinder, Spheres and Tube for
Transportation of Dangerous Goods as applicable.
Cylinders must be stored outdoors in a well-
ventilated area out of reach of children.
Disconnected cylinders must have threaded valve
plugs tightly installed and must not be stored in a
building, or any other enclosed area.
Storage of this appliance indoors is permissible only
if it has been disconnected from its fuel supply
(natural gas line or LP gas cylinder).
The LP gas cylinder supply system must be arranged
for vapor withdrawal.
The LP gas cylinder used must include a collar to
protect the cylinder valve.
When an LP model is not in use, the LP gas must be
turned off at the supply cylinder.