FIRETECH FT-4X6 Series Buku Petunjuk - Halaman 6
Jelajahi secara online atau unduh pdf Buku Petunjuk untuk Senter FIRETECH FT-4X6 Series. FIRETECH FT-4X6 Series 7 halaman. 4x6” headlights
Halaman CetakFREQUENTLY ASKED QUESTIONS
8.
Are they plug and play?
In most applications for fire apparatus manufactured in North America, the FireTech headlight drops right in
place and requires no additional wiring (other than the halo wires if desired). There are three exceptions:
A. If your fire apparatus does not have standard H4 plugs (different connector), an adaptor harness
may be required. Please contact HiViz for more information.
H4 (standard) plug
B. If your headlights do not operate at all when installed
In legacy headlight systems (halogen), it was not as important that the ground and power be in
the correct polarity orientation at the OEM. With LED headlights, it is critical to be wired with the
correct polarity for operation. If your headlights do not operate correctly, the most likely problem is
mismatching high/low/ground pins. To rectify, use a multimeter or test light to identify which wires
correspond to low beam, high beam, and ground on your apparatus, and move pins on FireTech
headlight to match. Pins can be popped out of the connector using a small flat screwdriver pressed in
to the back of the pin. Please contact HiViz technical support if you require assistance or would prefer
to have someone walk you through this process. It's totally acceptable to facetime our team and an
EVT will guide you through the process!
C. If your apparatus had a Daytime Running Light provision from the factory, a bypass or
reprogramming may be required.
This is very common in Canada and on some years of KME apparatus with EsKey multiplex systems.
While less common, it can occur on other apparatus as well. If the headlights flicker, flash, or do not
seem to operate properly post-installation, first verify all wiring is correct (low to low, high to high, and
ground to ground), then contact HiViz Tech support for more information. There has never been a fire
apparatus with 4x6 headlights we are unable to support remotely.
HiViz LED Lighting HiViz Lighting INC PO Box 565, Naples, NC 28760 Phone: 703-662-3458 Email: [email protected]
9007/9004 plug
(requires adaptor)
10
FREQUENTLY ASKED QUESTIONS
9.
Why is there a dark spot at about 25ft?
The FireTech headlights are designed to illuminate 3 distinct zones: the foreground (area between the bumper
and bottom of the low beam), the standard "low beam" zone, and the "high beam" zone. If you look at the
front of the headlight, the two angled circular optics on the front provide a fill-in light in that first foreground
zone. If those were turned "off", you would see a beam pattern much more similar to other over-the-road
vehicle headlight applications. With the FireTech headlights, those fill-in optics produce a high output wash
near the apparatus which helps illuminate areas near the apparatus when responding or on scene. The beam
pattern is different by design, not a design defect.
10.
Do they come with the buckets?
No. FireTech headlights are sold as individual replacement lamps for a sealed beam headlight. Buckets for
4x6 headlights are commercially available from various sources. Please contact HiViz for more info.
11.
What is the warranty?
FireTech headlights are guaranteed to be free from defects in materials and workmanship for the operational
service life of the apparatus which they were first installed. We are not in the headlight rental business and
request you do not move headlights from truck to truck. This warranty does NOT cover physical damage
(cracking, scratching, melting, etc).
HiViz LED Lighting HiViz Lighting INC PO Box 565, Naples, NC 28760 Phone: 703-662-3458 Email: [email protected]
11