AeraMax Professional Pro AM IIIS Panduan Memulai Cepat - Halaman 3

Jelajahi secara online atau unduh pdf Panduan Memulai Cepat untuk Pembersih Udara AeraMax Professional Pro AM IIIS. AeraMax Professional Pro AM IIIS 8 halaman.

Halaman Cetak

AeraMax Professional Pro AM IIIS Panduan Memulai Cepat

DISPLAY PANEL

NOTE: after the unit is turned on the "AQ" light will flash for a few minutes while the system self-calibrates.

HEPA FILTER REPLACEMENT INDICATOR –

This indicator will show

its status when the access panel is open or closed. If the light is red this indicates the filter

needs replacing. The replacement period will vary depending on the filters used, hours of

use, air quality, and rate of air flow. For filter replacement indicator descriptions see FILTER

REPLACEMENT INDICATORS section.

CARBON FILTER REPLACEMENT INDICATOR –

This indicator will

show its status when the access panel is open or closed. If the light is red this indicates

the filter needs replacing. The replacement period will vary depending on the filters used,

hours of use, air quality, and rate of air flow. For filter replacement indicator descriptions

see FILTER REPLACEMENT INDICATORS section.

ACCESSORY INDICATOR –

This indicator will show its status when the access

panel is open or closed. This indicator will only be used if an accessory filter is installed in

the unit. If the light is red this indicates the filter needs replacing. The replacement period

will vary depending on the filters used, hours of use, air quality, and rate of air flow. For

filter replacement indicator descriptions see FILTER REPLACEMENT INDICATORS section.

AIR QUALITY SENSOR –

This indicator will show its status when the access

panel is open or closed. This indicator monitors the air quality and adjusts the fan speed to

keep your air purified. Blue, amber, and red lights indicate the purity of your air.

OPERATION

The air purifier continuously works in automatic mode; the user can select which preference they would like the purifier to use based on the location or desired operation of the air

purifier. The purifier will operate through a minimized range of speeds, not exceeding the maximum level selected, in order to run quietly while cleaning the room of contaminants.

Once air is cleaned, and no sensors are activated, the unit lowers to energy saving mode to reduce energy consumption and extend the life of the filters.

When Auto Mode is selected, the Auto mode indicator will be blue. This mode uses the EnviroSmart ™ technology to monitor the air quality, motion and noise level to adjust the

fan speed in order purify your air as quickly as possible. Once air is cleaned, and no sensors are activated, the unit lowers to energy saving mode to reduce energy consumption

and extend the life of the filters.

The machine will continue to use EnviroSmart ™ but only utilizes the 3 lowest, most quiet of the 5 fan speeds.

When Manual Mode is selected, the Manual mode indicator will be blue. This mode allows you to choose one of the 5 fan speeds and keep unit at this speed until Auto Mode is

chosen/selected. EnviroSmart™ sensors will NOT adjust the fan speed in this mode.

SET UP

1. Open unit by pressing the latches on both sides.

2. Remove bag(s) from filter(s) and place back in the unit.

3. Plug the IEC plug into the power cord socket on the back of the unit.

AeraMaxPRO_AMIIIS_AM3SPC_411643_18L_071219.indd 4-5

AUTHOR:

M. GARTZ

PlasmaTRUE™ TECHNOLOGY –

This indicator will show its status when

the access panel is open or closed. Creates an ionized field to help safely remove airborne

pollutants. To turn on and off the PlasmaTRUE™ TECHNOLOGY, touch and hold the PLASMA

indicator. A blue light illuminates when the PlasmaTRUE™ TECHNOLOGY is enabled. To disable

the PlasmaTRUE™ TECHNOLOGY, press and hold "Plasma" indicator until light is off.

AUTO MODE –

To select, press and hold the button until the icon illuminates. This mode

uses the EnviroSmart ™ technology to monitor the air quality, motion and noise level to adjust the

fan speed in order to purify your air as quickly as possible. This button also includes QUIET MODE.

To select, press and hold until the button turns purple. The machine will continue to use EnviroSmart

™but only utilizes the 3 lowest, most quiet of the 5 fan speeds.

MANUAL MODE –

To select, press the button until the icon illuminates. This mode

allows you to choose one of the 5 fan speeds and keep the unit at this speed until AUTO MODE

is chosen again. The internal sensors will not adjust the fan speed in this mode.

FAN SPEED INDICATORS –

The fan has 5 speeds and can reach turbo speed

to clean the room in case of high levels of contaminants. The number of bars illuminated

indicates fan speed.

1 – whisper

4 – high

2 – low

5 – turbo

3 – medium

CARE AND MAINTENANCE

CLEANING:

• Clean external housing as necessary by wiping with a dry, soft cloth; for stains, use a warm, damp cloth.

• Do not use volatile fluids such as benzene, paint thinner, scouring powder or other cleaners that may damage the unit surface.

• Clean intake and exhaust vents by wiping with a dry, soft cloth.

FILTER REPLACEMENT INDICATORS:

The replacement filter indicators will signal when to replace the HEPA Filter and/or Carbon with Pre-Filter. The replacement period will vary depending on the

hours of use, air quality, and rate of air flow. However, under normal usage, most HEPA Filters need to be replaced every 2 years, and Carbon with Pre-Filter

every 6 months. When a filter needs to be replaced the following color will be shown on any one of the HEPA, CARBON, or ACCESSORY filter replacement

indicators:

Red flashing = 90% filter wear (recommendation to order new filters)

Red steady = 100% filter wear (replace with new filters)

Do not wash and reuse any of the filters – they will not work effectively. Only use AeraMax ® PRO brand replacement filters as units will not function using

any other replacements.

FILTER REPLACEMENT PROCEDURE:

Unlock access panel: to unlock, insert the

Open front access panel by pressing latches

key provided and rotate counter-clockwise

on both sides of unit. Allow panel to open

¼ turn.

fully. Remove filter(s) to be replaced.

FILTER REPLACEMENT:

When installing a new filter the unit will automatically detect the filter type but the user will have to manually reset the filter replacement indicators.

To reset any of the filter replacement indicators use the following procedure:

Touch and hold the illuminated

Release finger from indicator.

indicator for three seconds until

a beep is heard and the indicator

is flashing green.

Note: If you do not complete step three within 10 seconds of completing step 1 then the indicator light will not be reset.

TROUBLESHOOTING

PROBLEM:

POSSIBLE SOLUTION:

The air quality control system fails to start.

• Check to assure unit is connected to power supply.

• Make sure filters are genuine AeraMax

brands. IMPORTANT: Make sure filter detection area on genuine AeraMax

replacement filter aligns with window in filter frame.

• Review "Re-Installing Filters" section for further detail.

• Make sure front access panel is closed completely.

• Make sure power switch is on.

The unit makes a faint ticking sound.

• This indicates that the "PlasmaTRUE™" bipolar ionizer is working.

The HEPA and/or Carbon Filter replacement indicator light

• Repeat filter light reset instruction.

remain lit after replacing the filter(s).

Remove any packaging wrap from the

new filters(s) and re-install the filters.

Touch and hold the indicator for three

seconds until a beep is heard and the

indicator light turns off.

PRO filters, as unit will not function with other

PRO

7/12/19 3:10 PM