ERGODYNE 19661 Panduan Memulai Cepat
Jelajahi secara online atau unduh pdf Panduan Memulai Cepat untuk Peralatan ERGODYNE 19661. ERGODYNE 19661 6 halaman. Power tool trap
Halaman Cetak
SQUIDS
TOOL ATTACHMENTS
POWER TOOL TRAP
WWW.ERGODYNE.COM // 800 225 8238
Fig. 1
Fig. 3
Fig. 5
Fig. 7
®
™
Fig. 2
Fig. 4
Fig. 6
WARNINGS: All warnings and instructions must be read and understood before using this
product. Failure to do so may result in property damage, serious injury, or death.
• Never exceed the allowable dimensions for any Power Tool Trap™:
•
Model 3780L is designed for power tool batteries up to: LENGTH: 5in / 12.5cm,
WIDTH: 3.5in / 9cm, HEIGHT: 3.5in / 9cm
•
Model 3780S is designed for power tool batteries up to: LENGTH: 3.5in / 9cm,
WIDTH: 2.75in / 7cm, HEIGHT: 2.5in / 6.5cm
• Always inspect Tool Attachments prior to, and after, each use (refer to INSPECTION
instructions).
• Do not wrap Tool Attachments around sharp or rough edges.
• Never modify or alter your Tool Attachments.
• Never modify a tool that could result in manufacturer guideline deviation.
• Do not use this product if it interferes with the tool's safe working condition.
• Use extra precaution around moving machinery or parts, electrical hazards, chemical
hazards or other apparent hazards.
INSTRUCTIONS
1. Un-strap both hook and loop straps and open the Power Tool Trap™ [fig. 1]
2. Insert the power tool battery into the Power Tool Trap™. The front of the battery
should be facing the V-shaped opening of the trap and the circular D-Ring should
extend off the back. [fig. 2]
3. Take the vertical hook and loop strap and wrap it around the bottom of the Power
Tool Trap™ [fig. 3]. Make sure the strap is pulled down tight. [fig. 4]
4. Feed the horizontal hook and loop strap through the square metal pass-through loop.
[fig. 5]
5. Pull the strap tightly and secure it near the Trap back. [fig. 6]
6. Attach a tool lanyard to the D-Ring to complete an appropriate tethering system [fig.
7] (refer to Using A Tethering System instructions).
*For further instructions, watch the product video on www.ergodyne.com
All tools and/or equipment used in conjunction with a Power Tool Trap™ should be
regularly inspected by a competent person. Ensure any associated tethering system
is properly attached to the trap/tool and is not damaged. If any part of the tethering
system—including a Power Tool Trap™—has knowingly been involved in a drop, it must
immediately be taken out of service and replaced (refer to Using A Tethering System
instructions).
USING YOUR TETHERING SYSTEM
1. Always keep tools tethered while at heights. When exchanging tools, use one of the
following methods:
a. Use a 100% tie-off by ensuring the tool is tethered to a secondary anchor—or
secured in a rated container—before disconnecting from the initial anchor point.
b. Exchange tools over a secure area. (e.g. Inside a controlled container, over a
platform, etc.).
2. Required clearance:
a. When using Squids® Tool Attachments, determine the fully extended length of the
lanyard used, plus the length of the tool between where the lanyard is anchored
and the nearest person or sensitive object.
INSPECTION
Inspect your tethering system before and after each use. All equipment should be
regularly inspected by a competent person. Ensure the tethering system is properly
attached to the tool and is not damaged.
Before each use, check the following:
• Examine webbing, stitching and other soft materials for cuts, tears, heat trauma or
other damage.
• Examine all hardware for rust or corrosion, abnormal distortion (twists, bends), cracks
or breaks, or any other damage.
• Ensure carabiners and their gates function and lock properly. Examine swivels,
modular buckles, and any other components, to ensure proper function and that there
is no damage.
• Examine markings on the product and labels for legibility.
• If any part of the tethering system has knowingly been involved in a drop, it must
immediately be taken out of service and replaced. If any tethering system component
fails any part of an inspection, discard and replace the product immediately.
STORAGE AND CARE
• Store tool lanyards in a clean, dry location away from direct sunlight.
• To clean, use mild soap and water. Air dry.
DISCLAIMER
In no event shall Tenacious Holdings, Inc., be liable for any direct, indirect, punitive,
incidental, special, or consequential damages arising out of, or associated with, the misuse
of Squids® tethering system components (tool lanyards or attachments).
WARRANTY: We stand behind everything we make and guarantee our products to be
free of defects in materials and workmanship to the original purchaser for the product's
lifetime. Damage, abuse, and/or normal wear are not covered. Questions? Call Ergodyne
at +1-651-642-9889 (8 a.m. - 5 p.m. CST) or 800-225-8238.