Xerox DocuColor 5799 Panduan Memulai - Halaman 7

Jelajahi secara online atau unduh pdf Panduan Memulai untuk Mesin fotokopi Xerox DocuColor 5799. Xerox DocuColor 5799 46 halaman. Digital color copier/printer system
Juga untuk Xerox DocuColor 5799: Panduan Referensi (7 halaman), Panduan Referensi (7 halaman), Panduan Referensi (9 halaman), Panduan Tambahan (8 halaman), Panduan Referensi (7 halaman)

Halaman Cetak

ipaddress—Specifies the IP address assigned to the color server. This parameter is

required. If dhcp_client is set to yes and no DHCP services are found on the network, the

specified IP address is used. The default value for ipaddress is 192.168.0.254.

subnetmask—Specifies the subnetmask assigned to the color server. This parameter is

required. If dhcp_client is set to yes and no DHCP services are found on the network, the

specified subnet mask is used. The default value for subnetmask is 255.255.255.0.

defaultgateway0—Specifies the permanent IP address assigned to the gateway or router.

This parameter is ignored if there is no value after the equal sign (=), which is the default.

nameserver0—Specifies the permanent IP address assigned to the gateway or router.

This parameter is ignored if there is no value after the equal sign (=), which is the default.

workgroup—Specifies the Windows domain or Windows Workgroup to which the color

server belongs. The name can be up to 15 characters long. Valid values are alphanumeric

characters and underscores. The name cannot include spaces or periods. If the network

does not use Windows domains or Workgroups, leave this parameter blank (default).

nt_domain_controller—Specifies the IP address of the NT domain controller for the color

server. If an NT domain controller does not exist, leave this parameter blank (default).

wins_server—Specifies the IP address of the WINS server for the color server. If a WINS

server does not exists, leave this parameter blank (default).

zone—Specifies the name of the AppleTalk zone that the color server uses for Macintosh

printing. The name can contain up to 32 characters. Valid values are alphanumeric char-

acters, underscores, spaces, and periods. If Macintosh workstations are not printing to the

color server, leave this parameter blank (default).

The DP.INI file contains two sections of parameters called Printer 0 and Printer 1: one section

for configuring the color server print queue and the other for configuring the color server hold

queue. Each section contains the following parameters, where # can equal either 0

(parameters in Printer 0 section) or 1 (parameters in Printer 1 section):

pq#—Specifies the color server printer name that is used for lpd queue, Windows printer

sharename, and AppleTalk LaserWriter name. Valid values are alphanumeric characters

and underscores. The name cannot include spaces or periods. The default value for

Printer 0 is Splash_print. The default value for Printer 1 is Splash_hold.

pq#device—Specifies the copier to which the color server is connected. Valid values are

5750 (DocuColor

pq0device and pq1device must be identical.

pq#type—Specifies the type of queue: print or hold. Valid values are PRINT (print queue),

and HOLD (hold queue).

pq#wintcp—Enables/disables the color server support for TCP/IP protocol. Valid values

are on (enable support) and off (disable support). The default value is on.

pq#ethertalk—Enables/disables the color server support for AppleTalk protocol. Valid val-

ues are on (enable support) and off (disable support). The default value is on.

0015647-0001 February 18, 1999

5750), 5790, and 5799 (DocuColor

Getting Started Guide

5799). Note that the values for

page-7