Yamaha RX-V767 Panduan Referensi Cepat - Halaman 3
Jelajahi secara online atau unduh pdf Panduan Referensi Cepat untuk Penerima Yamaha RX-V767. Yamaha RX-V767 9 halaman.
Halaman Cetak
1
1
Connect the speakers
Front speaker
R
L
HDMI 2
HDMI 2
HDMI 3
HDMI 3
HDMI 4
HDMI 4
FRONT
CENTER
MOTE
MOTE
+12V
+12V
0.1A MAX.
0.1A MAX.
ER OUT
ER OUT
CENTER
CENTER
ND
ND
SUR.BACK
SUR.BACK
SUBWOOFER
SUBWOOFER
AUDIO
AUDIO
ZONE2
ZONE2
OUT
OUT
OUT
OUT
Center speaker
Connecting speakers
3
F R
O N
T
2
2
4 4
Connecting the subwoofer
1
Connect the subwoofer input jack to the
SUBWOOFER 1 or 2 jack on this unit with an
audio pin cable.
Surround
Surround back
speaker
speaker
R
L
R
L
7.1
7.1
6.1
HDMI 5
HDMI 5
SPEAKERS
SPEAKERS
SURROUND
SURROUND BACK/
BI-AMP
ZO
ZO
SINGLE
SINGLE
SINGLE
CENTER
CENTER
FRONT
FRONT
SURROUND
SURROUND
SUR.BACK
SUR.BACK
1
SUBWOOFER
OOFER 2
2
PRE OUT
PRE OUT
Subwoofer
1
7.1
Connect when using with 7.1-channel speaker layout.
6.1
Connect when using with 6.1-channel speaker layout.
Caution:
• Remove the AC power cable of this unit from the power outlet
before connecting the speakers.
• Generally speaker cables consist of two parallel insulated
cables. One of these cables is a different color, or has a line
running along it, to indicate different polarity. Insert the different
colored (or lined) cable into the "+" (positive, red) terminal
on this unit and the speakers, and the other cable into the "-"
(minus, black) terminal.
• Be careful that the core of the speaker cable does not touch
anything or come into contact with the metal areas of this unit.
This may damage this unit or the speakers. If the speaker cables
short circuit, "CHECK SP WIRES!" will appear on the front panel
display when this unit is switched on.
• This unit is confi gured for 8 Ω speakers at the factory setting.
When connecting 6 Ω speakers, confi gure the speaker
impedance setting of this unit to 6 Ω. When this unit is
confi gured for 6 Ω speakers, 4 Ω speakers can also be used as
the front speakers. For more information on setting the speaker
impedance, refer to "Changing speaker impedance" in the
Owner's Manual.
• When connecting the presence speakers, refer to "Presence speaker
connection" in the Owner's Manual.
• This unit can connect speakers that support Bi-amp connection for front
speakers. Refer to "Bi-amp connection" in the Owner's Manual for the
details.
1
Remove approximately 10 mm of insulation from
the ends of the speaker cables, and twist the bare
wires of the cables together fi rmly so that they will
not cause short circuits.
2
Loosen the speaker terminals.
3
Insert the bare wire of the speaker cable into the
gap on the side of the terminal.
4
Tighten the terminal.
2
Set the subwoofer volume as follows.
Volume: Set to approximately half volume (or slightly less than half).
Crossover frequency (if available): Set to maximum.
VOLUME
MIN
Subwoofer examples
- 3 -
CROSSOVER/
HIGH CUT
MAX
MIN
MAX