Directed Directechs DB3 Panduan Instalasi - Halaman 5

Jelajahi secara online atau unduh pdf Panduan Instalasi untuk Alarm Mobil Directed Directechs DB3. Directed Directechs DB3 20 halaman. Smart key for 2013 toyota highlander
Juga untuk Directed Directechs DB3: Panduan Instalasi (20 halaman), Panduan Instalasi (19 halaman), Manual (6 halaman), Panduan Instalasi (18 halaman), Panduan Instalasi (18 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (10 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (10 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (18 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (18 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (18 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (18 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (18 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (17 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (18 halaman)

Halaman Cetak

Directed Directechs DB3 Panduan Instalasi

Pre-installation and application warnings

This section highlights important information for this specific firmware and will assist in pricing accordingly, as

START

HERE

well as bringing awareness to any operational or vehicle limitations.

Compatibilities and Requirements

T-Harness

T-Harness is not compatible.

compatible

Vehicle Takeover

Firmware notes

OEM Remote Starter: Before programming your module, you must first check if your vehicle is equipped with an OEM remote

starter and disable it. If the vehicle is equipped with an OEM remote starter, whether Active or Inactive, it MUST be temporarily

disabled or permanently disconnected depending on the vehicle. Please refer to the "OEM remote starter information" section of the

guide for additional details. Also, to remote start the engine, all doors must be closed.

Note: In some cases, the module will program to the vehicle even if equipped with an OEM starter, but will prevent the aftermarket

remote start from functioning properly.

Motorized Hatch: If available, the Motorized Hatch feature needs to be enabled using the configuration tool found on the module

flashing page on www.directechs.com.

Keyless and Smart Key: Will remain functional during remote start.

All connectors are displayed from the wire side (unless specified otherwise).

Refer to the "Vehicle connections" following the installation diagram.

Footnotes

[1] Hood pin: The installation of an aftermarket hood pin is only required on vehicles that are not equipped with a factory hood pin, or if

not supported in data.

[2] Tach wire: An optional connection required on some remote starters, which do not support a tach signal in D2D.

[3] Push-to-Start: Connection required only if Pit-Stop / Idle mode is desired.

[4] Telematics Interrupt: Depending on the production date of your vehicle, if remote start fails, a telematics interrupt may be required.

403.TL3 4.12 2012 Lexus LS 460 (Smart Key)

The engine will stop when a door is opened.

Keys required for

Keys required

programming

for operation