Directed Directechs DB3 Panduan Instalasi - Halaman 10

Jelajahi secara online atau unduh pdf Panduan Instalasi untuk Alarm Mobil Directed Directechs DB3. Directed Directechs DB3 20 halaman. Smart key for 2013 toyota highlander
Juga untuk Directed Directechs DB3: Panduan Instalasi (20 halaman), Panduan Instalasi (19 halaman), Manual (6 halaman), Panduan Instalasi (18 halaman), Panduan Instalasi (18 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (10 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (10 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (18 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (18 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (18 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (18 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (18 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (17 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (18 halaman)

Halaman Cetak
Directed Directechs DB3 Panduan Instalasi

Module programming

Refer to "LED diagnostics and troubleshooting" for more information and for troubleshooting purposes.
For
Convenience-Only
programming, see next section.
IMPORTANT!  The vehicle battery must be in good condition and fully charged for successful
1
programming. A battery charger may be connected during programming if necessary.
The harnesses must be connected in this exact order:
  a) Connect the 14-pin.
2
  b) Connect the 12-pin.
  c) Connect the 10-pin.
When the LED turns ON solid red, proceed with the next step.
With the brake depressed, press the Push-to-Start (PTS) button once (1) to start the vehicle.
The LED flashes orange quickly for approximately 5 seconds, then flashes green (it may flash
green for 30-60 seconds).
3
Note: If the LED flashes red 3 or 4 times after the initial 25 seconds, wait an extra 30
seconds.
If the LED turns ON solid green for 3 seconds then shuts OFF:
Press the PTS button once (1) more to turn ignition OFF.
You have successfully completed the module programming sequence.
4
If the LED starts flashing orange slowly, follow the Key2GO programming below.
Key2GO programming:
Press the PTS button once (1) more to turn ignition OFF, remove the module from the vehicle,
and reconnect it to your computer. The web site will automatically recognize that you are
moving onto the second phase of the programming sequence. Proceed with next step.
5
Click on Submit Key2GO Request.
Once the configuration is completed, reconnect the module.
The LED turns ON solid green for 3 seconds, then shuts OFF.
6
If however, the LED returns to flashing orange slowly, perform a soft reset on the module.
When the LED turns solid red, start the vehicle. The LED will turn ON solid green for 3
seconds then shuts off.
You have successfully completed the module programming sequence.
10
403.HONDA9 2.07 2023 Honda Civic (Smart Key)
©2023 Directed. All rights reserved.