Directed Directechs DB3 Panduan Instalasi - Halaman 13

Jelajahi secara online atau unduh pdf Panduan Instalasi untuk Alarm Mobil Directed Directechs DB3. Directed Directechs DB3 20 halaman. Smart key for 2013 toyota highlander
Juga untuk Directed Directechs DB3: Panduan Instalasi (20 halaman), Panduan Instalasi (19 halaman), Manual (6 halaman), Panduan Instalasi (18 halaman), Panduan Instalasi (18 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (10 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (10 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (18 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (18 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (18 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (18 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (18 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (17 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (18 halaman)

Halaman Cetak
Directed Directechs DB3 Panduan Instalasi

LED diagnostics and troubleshooting

This section provides LED diagnostics and troubleshooting information to guide you through the various stages of your installation.
Module Programming
LED
Description
Module has no power.
Off
Waiting to begin the programming
sequence.
Solid red
Initialization failed.
Flashes green & red
Transponder functions were skipped.
Solid orange
All required CAN networks has been
detected.
Flashes green
1 of 2 CAN networks has been detected.
Flashes orange
Key2GO initiated.
Flashes orange
slowly
Module was successfully programmed with
all functions.
Solid green x 3 secs
Module was successfully programmed
without transponder functions.
Solid orange x 3 secs
Module Programming - Error codes
LED
Description
CAN2 not detected.
Flashes red x 1
J1850 not detected.
Flashes red x 1
CAN1 not detected.
Flashes red x 2
Bypass data not detected.
Flashes red x 3
Bypass processing error.
Flashes red x 4
ISO 1 not detected.
Flashes red x 5
ISO 2 not detected.
Flashes red x 6
MUX not detected.
Flashes red x 7
Skip programming.
Flashes red x 11
BCM programming.
Flashes red x 12
13
403.VW18 2.05 2024 Volkswagen Jetta GLI (Smart Key)
©2023 Directed. All rights reserved.
Troubleshooting
Make sure the D2D harness is connected and that 12 Volt is present between the red and black wires. If
12 Volt is present, the module may be defective.
Ensure the correct programming procedure is being followed.
Reset the module and complete the programming again. If the issue persists, please contact Technical
Support.
(If compatible) when RXT mode is not desired or convenience features are needed, please reset the and
reprogram the module.
Normal operation.
Normal operation.
Please follow the steps indicated in "Module programming" to complete the Key2GO programming.
Normal operation.
Normal operation.
Troubleshooting
Check the CAN2 Orange/Green and Orange/Brown wire connections. Wake up the data bus by
turning the ignition on and try again. If your installation does not require this connection, skip this step by
pressing the programming button 5 times.
Check the J1850 wire connection. Wake up the data bus by turning the ignition on and try again.
Check the CAN1 Tan and Tan/Black wire connections. Wake up the data bus by turning the ignition on
and try again. If your installation does not require this connection, skip this step by pressing the
programming button 5 times.
Check the bypass line connection. If more than one wire is used, make sure they are not inverted. Ensure
the vehicle still operates correctly using the factory key.
The bypass calculation failed. Reset the module and try again. If the condition persists, please contact
Technical Support.
The Yellow/Black wire did not detect the expected signal. Refer to "Installation (wiring diagrams &
vehicle wiring reference charts)" to check the connections.
The Orange/Black wire did not detect the expected signal. Refer to "Installation (wiring diagrams &
vehicle wiring reference charts)" to check the connections.
The Violet/Green or Violet/Brown wire did not detect the expected voltage value. Refer to "Installation
(wiring diagrams & vehicle wiring reference charts)" to check the connections.
If the BCM programming still fails after making sure doors are unlocked, press on the programming
button 5 times to skip this step.
Failed to program the BCM. Click Unlock on the OEM remote to solve the problem.