Zanussi FL 1089 Panduan Pengguna - Halaman 20
Jelajahi secara online atau unduh pdf Panduan Pengguna untuk Mesin cuci Zanussi FL 1089. Zanussi FL 1089 26 halaman. Washing machine fl 1089; fl 1089alu; fl 1289
Halaman Cetak
12. Start the programme
Press the START/PAUSE button. The relevant light
will stop flashing, the DOOR LOCKED light will light
up, and only the light relevant to the phase that is in
progress will remain lit.
If you have chosen a delayed start, the washing
machine will begin the countdown.
The display will show the duration of the programme
or the selected delay.
13. How to change a programme
during its cycle
Before you make any change, you must pause the
washing machine by pressing the START/PAUSE
button.
It is possible to change any phase before the
programme carries it out.
Changing the type of fabric or temperature is
possible, obviously, only during the washing phase.
When you make a change in these two parameters,
the washing machine will resume the cycle from the
beginning.
If it is necessary to drain the water in order to change
the programme in progress, proceed as follows:
• PAUSE the machine by pressing the
START/PAUSE button;
• press the RESET (ANULAR) button repeatedly,
until only the DRAIN
• press the START/PAUSE button again.
When the water has been drained, the display shows
a blinking zero. You may now select a new
programme and press the START/PAUSE button to
start it.
14. How to cancel a programme
during its cycle
To cancel a programme that is being carried out, first
pause the washing machine by pressing the
START/PAUSE button, then press the RESET
(ANULAR) button repeatedly, until the display shows
three blinking dashes.
15. How to open the door during
a programme
You can open the door, after having set the washing
machine to PAUSE, provided the following
conditions exist:
• the washing machine is not in the heating phase
beyond 55°C;
• the level of the water is not high;
light remains lit;
• the drum is not turning.
If these requirements are met, when you pause the
washing machine, the DOOR LOCKED light goes
out and the door can be opened.
Should it not be possible to open the door, and
should it be absolutely necessary to do so, switch
the machine off by pressing the ON/OFF button.
After approximately 3 minutes, you can open the
door.
Pay attention to the level and temperature of the
water in the washing machine!
When you close the door and press the ON/OFF
button again, the washing machine will resume the
programme from the point where it had been
interrupted.
16. End of programme
At the end of the programme, the washing machine
stops automatically, gives an audible signal, and
displays a blinking zero.
If you had selected the NIGHT WASH (CICLO
NOCHE) option, the START/PAUSE button light
flashes to indicate that the water must be drained.
The display shows a steadily lit zero.
When the programme has been completed, a
blinking zero appears on the display and the audible
signal is given.
The DOOR LOCKED light goes out at once.
Press the RESET (ANULAR) button repeatedly to
erase the programme that has just been carried
out. If you omit to do this, the next time you
switch the washing machine on, the blinking zero
will appear on the display and you will hear the
audible signal.
Note: when you switch the machine on, if you must
erase the previously performed programme, it is also
sufficient to press the FABRIC (TEJIDOS) button
and select a new programme.
Press the ON/OFF button to switch the machine off.
The relevant light will go out.
Remove the laundry from the washing machine.
Check whether the drum is completely empty, by
rotating it with your hand. The purpose of this is to
prevent any items of laundry from remaining
accidentally in the drum, where they might get
damaged in a subsequent wash (e.g. by shrinking) or
bleed colour into another load of laundry.
We advise you to close the water supply tap and
disconnect the plug from the socket.
Leave the door ajar in order to air the washing
machine.
44