Zanussi ZGG66424 Panduan Pengguna - Halaman 4

Jelajahi secara online atau unduh pdf Panduan Pengguna untuk Kompor Zanussi ZGG66424. Zanussi ZGG66424 16 halaman. Gas hob
Juga untuk Zanussi ZGG66424: Panduan Pengguna (16 halaman), Panduan Pengguna (16 halaman), Panduan Pengguna (21 halaman)

Halaman Cetak

– Cut off the mains cable where it connects with the

appliance and discard it.

– Flat the external gas pipes if there are fitted.

Installation

Warning! The following instructions about

installation, connection and maintenance must be

carried out by qualified personnel in compliance with

standards and local regulations in force.

Important safety requirements

This hob must be installed in accordance with the Gas

Safety (Installation and Use) Regulations (Current Edition)

and the IEE Wiring Regulations (Current Edition).

For appliances installed in the Republic of Ireland please

refer to NSAI- Domestic Gas Installation I.S. 813 Current

Editions and the ETCI Rules for Electrical Installations.

Provision for ventilation

Detailed recommendations are contained in the following

British Standards Codes Of Practice: B.S. 6172/ B.S.

5440, Par. 2 and B.S. 6891 Current Editions.

The hob should not be installed in a bed sitting room with

a volume of less than 20 m³. If it is installed in a room of

volume less than 5 m³ an air vent of effective area of 100

cm² is required. If it is installed in a room of volume be-

tween 5 m³ and 10 m³ an air vent of effective area of 50

cm² is required, while if the volume exceeds 11 m³ no air

vent is required.

However, if the room has a door which opens directly to

the outside no air vent is required even if the volume is

between 5 m³ and 11 m³.

If there are other fuel burning appliances in the same

room, B.S. 5440 Part 2 Current Edition, should be consul-

ted to determine the requisite air vent requirements.

For appliances installed in the Republic of Ireland please

refer to the NSAI- Domestic Gas Installation I.S. 813 Cur-

rent Editions Table Four.

Location

The hob may be located in a kitchen, a kitchen/diner or

bed sitting room (with a volume greater than 20 m³), but

not in a bathroom or shower room.

The minimum distance combustible material can be fitted

above the hob in line with the edges of the hob is 400

mm. If it is fitted below 400 mm a space of 50 mm must

be allowed from the edges of the hob.

– Speak to your local authorised facilities for disposal

of your appliance.

For appliances installed in the Republic of Ireland please

refer to NSAI- Domestic Gas Installation I.S 813 Current

Edition Section 7- Permitted Locations of Appliance.

Gas Connection

Warning! Any gas installation must be carried out

by a GAS SAFE REGISTER installer.

Make sure that, once the hob is installed, it is easily ac-

cessible for the engineer in the event of a breakdown.

The manufacturer will not accept liability, should the

above instructions or any of the other safety instructions

incorporated in this instruction booklet be ignored.

On the end of the shaft, which includes the G 1/2" threa-

ded elbow, adjustment is fixed so that the washer is fitted

between the components as shown in the diagram. Screw

the parts together without using excessive force.

End of shaft with nut

Washer

Elbow

Connection to the gas supply should be with either rigid

or semi-rigid pipe, i.e. steel or copper.

The connection should be suitable for connecting to R 1/2

(1/2 BSP male thread).

When the final connection has been made, it is essential

that a thorough leak test is carried out on the hob and in-

stallation.

Make sure that the main connection pipe does not exert

any strain on the hob.

If you use flexible metal pipes make sure that they agree to

ISO 10380 and ISO 10807 standards. Be careful they do