Directed Directechs DB3 Panduan Instalasi - Halaman 14

Jelajahi secara online atau unduh pdf Panduan Instalasi untuk Elektronik Mobil Directed Directechs DB3. Directed Directechs DB3 20 halaman. Smart key for 2013 toyota highlander
Juga untuk Directed Directechs DB3: Panduan Instalasi (20 halaman), Panduan Instalasi (19 halaman), Manual (6 halaman), Panduan Instalasi (18 halaman), Panduan Instalasi (18 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (10 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (10 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (18 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (18 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (18 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (18 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (18 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (17 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (18 halaman)

Halaman Cetak
Directed Directechs DB3 Panduan Instalasi
 
Active Ground When Running (Status)
LED
Description
Ground When Running (Status) command
received.
Flashes green
Ignition ON command received.
Flashes red & orange
Start ON command received.
Flashes green quickly
PTS shutdown error.
Flashes red x 10
CAN bus incorrectly detected.
Flashes red x 21
Commands
LED
Description
LOCK command received.
Flashes orange x 1
UNLOCK command received.
Flashes orange x 2
TRUNK command received.
Flashes orange x 3
AUX1 command received.
Flashes orange x 4
AUX2 command received.
Flashes orange x 5
AUX3 command received.
Flashes orange x 6
Shutdown Codes
LED
Description
Takeover successful.
Flashes green x 1
Runsafe was not disabled.
Flashes red x 1
Brake was not detected.
Flashes red x 2
Smart key was not detected.
Flashes red x 3
Speed was detected.
Flashes red x 4
14
403.HONDA9 2.07 2023 Honda Civic (Smart Key)
©2023 Directed. All rights reserved.
Troubleshooting
The module has initialized the remote start sequence.
The module has received the Ignition ON command and is processing the remote start sequence.
The module has received the Start ON command and is processing the remote start sequence.
The PTS output from the module was not activated due to safety protection.
Verify the CAN1 and CAN2 connections. Refer to "Installation (wiring diagrams & vehicle wiring
reference charts)" to check the connections.
Troubleshooting
If the bypass module fails to flash, it did not receive the signal. Commands can come from RF or D2D.
If the bypass module fails to flash, it did not receive the signal. Commands can come from RF or D2D.
If the bypass module fails to flash, it did not receive the signal. Commands can come from RF or D2D.
If the bypass module fails to flash, it did not receive the signal. Commands can come from RF or D2D.
If the bypass module fails to flash, it did not receive the signal. Commands can come from RF or D2D.
If the bypass module fails to flash, it did not receive the signal. Commands can come from RF or D2D.
Troubleshooting
Normal operation.
No UNLOCK command was received prior to opening the door, or the 45 second timer expired in
takeover mode.
The brakes were not detected, which prevents the system from shutting down the vehicle.
The smart key was not detected, which prevents the system from shutting down the vehicle.
The vehicle was detected as moving, which prevents the system from shutting it down.