Directed Directechs DB3 Panduan Instalasi - Halaman 10

Jelajahi secara online atau unduh pdf Panduan Instalasi untuk Dengan kunci Directed Directechs DB3. Directed Directechs DB3 20 halaman. Smart key for 2013 toyota highlander
Juga untuk Directed Directechs DB3: Panduan Instalasi (20 halaman), Panduan Instalasi (19 halaman), Manual (6 halaman), Panduan Instalasi (18 halaman), Panduan Instalasi (18 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (10 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (10 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (18 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (18 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (18 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (18 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (18 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (17 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (18 halaman)

Halaman Cetak

Directed Directechs DB3 Panduan Instalasi

Module programming

Refer to "LED diagnostics and troubleshooting" for more information and for troubleshooting purposes.

Convenience-Only

For

programming, see next section.

Vehicle battery must be in good condition and fully charged for successful programming. A

battery charger may be connected during programming, if necessary.

The harnesses must be connected in this exact order:

1. Connect the 14-pin.

2. Connect the 12-pin.

3. Connect the 10-pin.

When the LED turns on solid red, proceed with the next step.

Turn the ignition ON.

The LED flashes orange quickly for approximately 5 seconds, then flashes green. It may flash

green for 25 seconds.

Note: If the LED flashes red 3 or 4 times after the initial 25 seconds, wait an extra 30

seconds.

If the LED starts flashing orange slowly, Key2Go programming will be required for your

vehicle.

Turn the ignition OFF, remove the module from the vehicle, and reconnect it to your computer.

The web site will automatically recognize that you are moving onto the second phase of the

programming sequence. Proceed to step 4.

If however, the LED turns ON solid green for 3 seconds, then shuts OFF, turn the ignition OFF,

and remove the key from the ignition barrel. The programming sequence was successfully

completed.

Click Submit Key2GO Request.

When the configuration is completed, reconnect the module.

The LED turns ON solid green for 3 seconds, then shuts OFF.

Remove the key from the ignition barrel.

If however, the LED returns to flashing orange slowly, perform a soft reset on the module.

When the LED turns on solid red, start the vehicle. The LED will turn ON solid green for 3

seconds then shuts off.

You have successfully completed the module programming sequence.

403.HONDA7 2.43 2019 Honda CR-V