Directed Directechs DB3 Panduan Instalasi - Halaman 6

Jelajahi secara online atau unduh pdf Panduan Instalasi untuk Dengan kunci Directed Directechs DB3. Directed Directechs DB3 19 halaman. Smart key for 2013 toyota highlander
Juga untuk Directed Directechs DB3: Panduan Instalasi (20 halaman), Panduan Instalasi (19 halaman), Manual (6 halaman), Panduan Instalasi (18 halaman), Panduan Instalasi (18 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (10 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (10 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (18 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (18 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (18 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (18 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (18 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (17 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (18 halaman)

Halaman Cetak
Directed Directechs DB3 Panduan Instalasi
Immobilizer interface
When possible use valet key for key wrap. If a blade key is used or
from OEM key (the OEM remote may differ from the models shown in the illustrations).
removed
Make sure to test and secure the loops before reassembling the vehicle.
Method 1: Key Wrap
4-6 loops
Note:
- Your OEM remote may differ from the model shown in the illustrations.
- Make 4-6 loops and place them around the front of the plastic body of the vehicle's coded key as shown above.
- Test and secure mounted loops before reassembling the vehicle.
Method 2: Immobilizer interface using 556UXL (sold separately)
Not all OEM remotes can be inserted in 556UXL because of their size.
Make sure the key will fit, otherwise it is recommended to use a different method.
Note: The discontinued 556U or 556UW can still be used for the installation.
Common Relay 2: Yellow/Red: 11
NO Relay 2: Brown/Red: 12
6
403.VW10 2.01 2008 Volkswagen Passat
©2023 Directed. All rights
The OEM immobilizer
receiver is located on the
underside of the steering
column, where the ignition
switch would normally be.
4-6 loops
if the vehicle is equipped with Keyless Entry
Common Relay 2: Yellow/Red: 11
NO Relay 2: Brown/Red: 12
Remove battery from
OEM Remote Control
Move 556UXL loop as close to the
front of ignition cylinder (OEM
Immobilizer Receiver) as possible.
Test and secure mounted loop
before reassembling the vehicle.
N/A: Green, pin 6
N/A: Violet, pin 5
(-) Ground: Black, pin 4
N/A: Pink, pin 3
(-) GWR: Blue, pin 2
(+)12V : Red, pin 1
, the battery must be
OEM
Immobilizer
Receiver
Black/White - NOT USED
Black/Red
Black
(+)12V