alphatronics AlphaVision CP 508 Panduan Pengguna - Halaman 3

Jelajahi secara online atau unduh pdf Panduan Pengguna untuk Panel Kontrol alphatronics AlphaVision CP 508. alphatronics AlphaVision CP 508 6 halaman.

Halaman Cetak

disarming.

2.2 Control Panel section arming

If a PIN-code is authorized to choose sections for arming or disarming, then the arming procedure can

be executed as follows: enter the PIN-code, press the key for the section to be armed (key 1, 2, 3 or F,

H, P). One of the LED's 1 to 3 will be turned on, depending on the selected section. Press the <#>-

key. The section will be armed and the horizontal dash will be turned on. In this way, only 1 section

can be armed at the same time. If 2 sections are to be armed, then this procedure should be repeated.

2.3 Control Panel HOME arming

If the control panel is enabled to use the HOME-arming mode, then the control panel will be turned to

HOME-arming by entering the PIN-code and pressing the <8>-key (HOME). The HOME-sections

(programmed by the installer) will be turned on and the LED AWAY will start flashing. The control

panel can be totally secured by entering the PIN-code and pressing <#> (see 2.1). If the control panel

was armed completely, then it can be set back to the HOME-arming mode by previously described

procedure. The non-HOME sections (programmed by the installer) will be disarmed.

2.4 Control Panel arming/disarming by key-switch

By activating the key-switch the corresponding section will be armed or disarmed.

2.5 Control Panel disarming completely

Enter PIN-code. Press <*>-key. All sections, where the entered PIN-code is authorized for, will be

disarmed.

2.6 Control Panel section disarming

If a PIN-code is authorized to choose sections for arming or disarming, then the disarming procedure

can be executed as follows: enter the PIN-code, press the key for the section to be armed (key 1, 2, 3

or F, H, P). One of the LED's 1 to 3 will be turned on, depending on the selected section. Press the

<*>-key. The section will be disarmed and the horizontal dash will be turned off. In this way, only 1

section can be disarmed at the same time. If 2 sections are to be disarmed, then this procedure should

be repeated.

2.7 Control Panel refuses to arm

When arming one or more sections, all instant and 24-hour zones have to be closed (corresponding

LED's have to be turned off), if not, then the ordered arming will not be executed.

If, at the moment of arming, an instant zone is open, then the display will show 'bP' alternated with

the number of the open zone. The keyboard generates an attention signal. The open zone can be

bypassed (isolated) by pressing the <8>-key. Are more zones open, then the next zone number will

appear on the display. Are all instant zones closed, then the ordered arming will be executed but the

bypassed zones will stay disarmed. If a zone of a section is isolated, then the rightmost digit of the

display will show the indication. After disarming the section, the bypass will automatically be

removed.

If, at the moment of arming, a 24-hour zone is open, then no message will appear on the display. A

short attention signal will be generated by the keypad and the ordered arming will not be executed. It

is not possible to arm with one ore more 24-hour zones open.

If all zones, that belong to the section that must be armed, are isolated, then it is not possible to arm

the section. If tried to arm a completely idle section then the attention signal will be generated for a

short moment and the ordered arming will be ignored.

2.8 Isolating zones

Before arming it is possible to enter some zones as isolated zones. After arming the isolated zones

remain disarmed. After disarming the section again, the isolation will be automatically removed.

Enter a PIN-code that is authorized for isolation. On the display appears 'iS'. LED's 1 to 9 indicate if

one of the zones 1 to 9 is already isolated. By pressing one of the keys <1> to <9> the zone will be

isolated and the LED will be turned on. By pressing again, the isolation will be removed. If the LED's

represent the desired programming, press <#>. The rightmost decimal point in the display will be

turned on. The LED's 10 and 1 to 6 now represent the isolation of the zones 10 to 16. If the desired

programming is shown then press <#>.

3. PROGRAMMING PIN-CODES

3.1 Programming pin-code systemsupervisor

Enter systemsupervisor PIN-code. Press <5>-key. The display shows 'C4'. Enter new 4-digit PIN-

code. The new systemsupervisor PIN-code is immediatly in affect. If not sure, which code was

entered, repeat described procedure immediatly before control panel returns to standby.

3.2 Programming authorization for pin-codes

Manual CP-508 versie 2.5

September 17th 1993

pg. 3