Nikon PROSTAFF 7 Buku Petunjuk - Halaman 8

Jelajahi secara online atau unduh pdf Buku Petunjuk untuk Alat Ukur Nikon PROSTAFF 7. Nikon PROSTAFF 7 41 halaman.
Juga untuk Nikon PROSTAFF 7: Buku Petunjuk (20 halaman)

Halaman Cetak

Target priority mode

This laser rangefinder employs the First Target Priority/Distant

Target Priority switching system (Factory default setting is

Distant Target Priority mode).

Distant Target Priority mode

First Target Priority mode

「

」

「

1. Turn on the power (Confirm the internal display is on).

2. Press and hold the MODE button, then depress and hold

the POWER ON/Measurement button within 0.5 second.

Continue to press and hold both buttons (more than

2 seconds) until First Target Priority mode and Distant

Target Priority mode are switched.

3. Release both buttons when the mode is switched.

* If the buttons are not pressed in the correct order,

switching will not take place.

* If switching fails to take place, repeat Step 2.

[First Target Priority mode/Distant Target Priority mode]

When measuring overlapping subjects, First Target Priority

mode displays the distance of the closest subject and

Distant Target Priority mode displays that of the farthest

subject.

Distance display units

Measurement results are displayed in yards/meters.

(Factory default setting is yard.)

Yard

[

]

Meter

1. Turn on the power (Confirm the internal display is

」

on).

2. Press and hold the MODE button for more than two

seconds. When the display unit has been switched,

release the button.

3. After the unit is set, results will be converted and

displayed in the selected distance display unit.

LED illumination

1. Turn on the power (Confirm the internal display is on).

2. By pressing the MODE button for less than 2 seconds,

the LED illumination can be turned ON and OFF.

* Use the LED illumination when conditions are too dark

to view the LCD panel.

* The LED illumination can also be turned off by turning

the laser rangefinder's power off. In this case, the

illumination will be off when the laser rangefinder's

power is turned on again.

Changing battery

• Type of battery: 3V CR2 lithium battery x1

• Battery remaining amount indicators

[

]

* Battery condition mark in the internal display warns when the battery needs to be replaced.

flashing

1. Open the battery chamber cover

Using the ball of the thumb, etc. in the recessed part of the battery chamber cover, rotate the cover in

the direction toward the

2. Replace the old battery with a new one

Insert a new battery with the [+] and [-] correctly positioned following the "Battery installation"

indication in the battery chamber. [+] pole should be towards the inside of the chamber. If the battery is

not inserted correctly, the laser rangefinder will not operate.

3. Close the battery chamber cover

Align the

thumb, etc., turn the cover towards the

for water resistance, but continue to turn it all the way until it stops. Confirm that the cover is securely

closed.

• Battery life

Continuous operation: Approx. 13,000 times (at approx. 20°C)

This figure may differ according to condition, temperature, and other factors such as target shape, color, etc. Use

only as a guide.

* The battery supplied with this Laser Rangefinder is for operation checking. Due to natural electrical discharge, the life of this

battery will likely be shorter than that noted above.

* If water enters the battery chamber due to submersion, dry the battery chamber well, then replace the battery.

: Battery has enough power for use.

: Battery level is getting low. Prepare to replace the battery.

: Battery level is low. Battery should be replaced with a new one.

: Battery is exhausted. After the indicator flashes three times, the laser rangefinder

automatically powers off. Please replace the battery.

mark. It may not open easily due to its rubber packing for water resistance.

mark with the indicator ● and insert the battery chamber cover. Using the ball of the

mark. It may not close easily due to the rubber packing