Cub Cadet 317-262-100 Panduan Pemilik - Halaman 9

Jelajahi secara online atau unduh pdf Panduan Pemilik untuk Peniup Salju Cub Cadet 317-262-100. Cub Cadet 317-262-100 20 halaman.

Halaman Cetak

1. Maintenance

Make sure that there is no moisture on the cord ends or

.r.

receptacles when plugging in the cord.

AWARNING

9. Push the starter button to crank the engine. Do not crank the

engine for more than 15 seconds without allowing the electric

' Do not use

starter to cool for around 10 minutes. Attempt further cranking

snow tltrower

only atter the starter has cooled down.

on surfaces

Do not push the primer button while the engine is

above ground

o"i"g

"I""k"d.

level' such as

Electric start engines can be severely damaged if you

the roof of a

do not follow proper starting instructions.

building'

Release starter button once

the engine starts and gradually

move the choke lever to the

OFF position.

Disconnect the power cord

from (i) household receptacle

and then from (ii) starter switch

on the snow thrower. Store the

cord in a dry place.

1 0

rnE-

S[ey away

frorn the front

of your snow

t|trcrer unit

whcn the

augGf is turn-

Ing.

Avoid plcking

up gravel

wfth the

augor since

this could

damage the

unit and/or

cause serious

injury to the

operator.

Always be

alert to the

hidden haz-

ardsthatmight

be struck by

the auger.

Should you

hit a foreign

object with

the auger

stop the

engine imme-

dlately,

remove key,

dlsconnect

sparkplugand

inspect the

machlne for

any damage.

Repair dam-

age before

operating the

unit again,

1 1 .

.--,/Y

;'-

Starter---=--.

itrS.Button\g

!v/

STO P P I NG

E N G I N E

THROWING

SNOW

. 1 .

2 .

.A.

Always disconnect power

r Ievn

cord from the household receptacle first, then unplug

t . 1

';i r-=\

\.{ir

\./

/ , /

{==/'

from starter switch.

Turn ignition key to the OFF position.

Remove the key from the switch if you are leaving the operating

position and/or before making repairs or adjustments.

Allow the unit to run for a few minutes before storing.

Note: Ihe snow thrower will be pulled forward by the auger as the

handle is raised. The unit will also move forward when the auger

comes in contact with the accumulated snow.

1. Before entering the area where snow needs to be cleared,

,adjust the position of the discharge chute so that snow will be

thrown in the desired direction.

Note: Snovv should not be thrown towards buildings, automobiles, or

people. Always try to throw snow down wind.

2. Adjust the deflector on top of the discharge chute up or down to

control the distance that the snow

will be thrown. See figure 6.

Disengage auger drive before

adiusting discharge deflector.

3. Review the area to be cleared of

snow and establish a pattern for

the most efficient snow removal.

4. Inspect the area for possible

obstructions like gravel and rocks.

Remove, if any.

5. Begin snow removal by clearing a

path down the center of a walk or

driveway along your pattern for snow removal. Gradually widen the

path throwing snow to both sides. Allow the snow thrower to move

the snow at its own pace.

When clearing wet and heavy snow, you may have to push down the

handle and dow down. But allow engine to work at f ull throttle'

Lower The

Chute For

Shorter

D i s t a n c e

F I G U R E 6

FIGURE 5