Armytek Partner C1 Pro Panduan Pengguna
Jelajahi secara online atau unduh pdf Panduan Pengguna untuk Senter Armytek Partner C1 Pro. Armytek Partner C1 Pro 2 halaman.
Juga untuk Armytek Partner C1 Pro: Panduan Pengguna (2 halaman)
Halaman Cetak
1. Always follow the instructions from this manual and recommendations on battery usage.
2. Apply only the recommended power sources.
3. Do not reverse battery polarity.
4. Do not use different power sources together, i.e. old ones with new ones, charged with
discharged. Do not use different types of batteries combined as the element with less
capacity can be damaged.
5. Do not modify or recast the flashlight and its components as it will deprive you of the
warranty.
6. Do not allow water or any other liquid to leak into the flashlight.
7. Do not aim a switched-on flashlight at people's or animals' eyes – it can cause temporary
blindness.
8. Do not allow children to use the flashlight without your assistance.
The producer will not be liable for any harm done to the user if it was caused by
improper use of the product.
Care and Storage
It is recommended to clean the threads and O-rings off dirt and old grease once or twice per year. Remember that reliable protection
from water and dust cannot be provided by worn out sealing. The fouling as well as lack of lubricant cause fast wear-out of threads and
sealing rings. To clean the threads do the following:
1. Unscrew the tailcap and remove the sealing ring carefully with a toothpick (do not use sharp metal things as they can damage the ring).
2. Wipe the sealing ring thoroughly with a soft cloth (or tissue). Do not use solvents. If the sealing ring is worn out or damaged
replace it by a new one.
3. Clean the metal threads with a brush using ethanol. Be careful not to allow the applied liquid to get inside the flashlight or tailcap as
it can cause fails in functionality of the flashlight.
After cleaning lubricate the thread and the sealing ring with polyalphaolefin-based silica grease, e.g. Nyogel 760G.The application of
automotive and other improper grease can cause swelling and damage of the sealing rings.
In case of active operation and exploitation in dusty environments, it is recommended to perform cleaning and lubricating of the parts
as often as required.
In case the rubber button is damaged, it should be replaced. You can also replace the switch with
the spring in the same way. Replacement order:
1. Unscrew the tailcap.
2. Unscrew the first washer inside it to take out the switch. To do so you should use needle-
nose pliers (round-nose pliers or another tool, the most suitable will be expansion pliers).
Use the tool as it is shown at the picture. To replace the rubber button unscrew the second
washer under the switch.
3. Replace the rubber button and assemble the parts in inverse sequence.
Do not disassemble the flashlight except for unscrewing the thread ring gage and replacing the rubber button. There are no
other parts in the flashlight that can be replaced by the user.
Service and Warranty
Armytek provides free warranty repair for 10 years from the date of purchase.
Warranty doesn't cover damage caused by:
1. Improper usage.
2. Attempts to modify or repair the flashlight by nonqualified specialists.
3. Longtime application in chlorinated or polluted water, or other liquids (other than water).
4. High temperatures and chemicals' exposure (including the exposure of liquid from defected batteries).
5. Usage of low-quality batteries.
Armytek Optoelectronics Inc.
Web: www.armytek.com Email: [email protected]
Address: 13-85 West Wilmot St, Richmond Hill, Ontario, L4B 1K7, Canada
Specifications are subject to change without notice.
Warnings
Partner
THE MOST TECHNICALLY ADVANCED
FLASHLIGHTS IN THE WORLD
USER MANUAL
Thank you for choosing the products of Armytek Optoelectronics Inc., Canada.
Please read this manual carefully before using the flashlight.
Armytek Optoelectronics Inc. is a Canadian manufacturer that produces powerful and reliable flashlights designed especially for your
needs. The components made in the USA and Japan.
10 years no-hassle warranty
Set description
2
1
3
Partner
Items included in the package:
1 - Flashlight
3 - Spare rubber button
2 - Clip
4 - Holster
Your flashlight can inconsiderably differ from the pictures in the manual.
ь
The producer reserves the right to change the package at his own discretion without modifying this manual.
ь
Initial Service
1.
2.
To set/replace batteries:
1. Unscrew the tailcap.
2. Place the batteries with the positive contact (+) facing the head of the flashlight.
3. Adjust the tailcap and tighten it as far as it can go.
We DO NOT RECOMMEND to leave power sources inside the flashlight for a long storage period, as batteries (especially, non-rechargeable)
can leak for various reasons and damage the inner parts of the flashlight. If you want to keep your flashlight in a stand-by state with batteries
in then use new and high-quality batteries and store the flashlight in acceptable for batteries operational temperature and revise the batteries'
state at least once a month. If you have noticed any signs of batteries' defects then withdraw them from the flashlight and utilize. It is also
recommended to replace discharged batteries with new ones before the storage as the chance of leakage is higher with discharged batteries.
.
5
x2
6
4
7
5 - Lanyard
7 - User manual
6 - 2 spare O-rings
3.