Dish Network Hopper Panduan Aktivasi dan Pengaturan
Jelajahi secara online atau unduh pdf Panduan Aktivasi dan Pengaturan untuk DVR Dish Network Hopper. Dish Network Hopper 2 halaman.
Juga untuk Dish Network Hopper: Setup Manual (16 halaman)
Halaman Cetak
Setup and Activation - Hopper
SCREEN
STEP
1
White tear drop (may
2
flash to a black screen)
015 (only on certain
2a
incorrectly on certain units;
units)
need to reset factory settings
3
833
4
015
Setup wizard: pair
5
remote (step 1 of 5)
Setup wizard: name
Assigns a room name to the
6
location (step 2 of 5)
Setup wizard: download
7
Hopper software download
software (step 3 of 5)
8
303
9
Hopper startup screen
10
833
11
015
Setup wizard: download
12
software (step 3 of 5)
Setup wizard: set
13
resolution (step 4 of 5)
756 (black screen while
14
setting)
15
Setup wizard: authorize
receiver (step 5 of 5)
16
"Watch TV" is available
17
on the screen
18
015
19
Live TV
RECEIVER ACTION
Hopper starting up
Factory software set
Check switch
Acquiring signal
Press the SAT button on the
Pairs remote to Hopper
Choose correct name for the
receiver
If there are multiple Hoppers,
Memory burn
Hopper reboots
If there are no more Hoppers
Check switch
to start up, complete Software
Acquiring signal
Joey software download
Sets TV resolution
Saves settings
Activate all receivers via tablet or
Activation process
Enter installation details in
Activation screen; hit sent
Authorization is complete
Continue entering installation
Acquiring signal
1. Configure Remote to TV (D)
EPG download
3. Move on to Joey setup
APPROX.
TECH ACTION
TIME
Plug in Hopper
00:10
Startup Actions (B)
02:02
01:30
Workaround (A)
02:31
Startup Actions (B)
03:22
00:04
Hopper remote
00:09
Hopper location
03:49
06:58
repeat steps 1-6
00:15
02:03
02:31
Download Actions (C)
04:47
Select TV resolution
00:09
Select "Yes"
00:08
03:09
DASH
04:08
ETAdirect
Select "Watch TV"
00:21
02:14
details in ETAdirect
2. Verify Client ID (E)
11:36
(B) Startup Actions
(A) Workaround
(07:55 total time)
A1. Press the MENU button
A2. Select the "Settings" tile
B1. Unwrap remote and batteries
A3. Select the "Factory
B2. Place batteries in the remote
Defaults" tile
B3. Put room/input sticker on remote
A4. "Warning 093" appears
B4. Fill out room and input
on screen
information in the GSG
A5. Select "Yes"
B5. Clean up Hopper box/other trash
B6. Take trash to the vehicle and
The Hopper will reboot;
bring back the vacuum
continue on with step 3
(C) Software Download Actions (20:23 total time)
C1. Open and unpack Joeys at each location
C2. Unwrap remotes and batteries
C3. Place batteries in each remote
C4. Place room/input stickers on each Joey remote
C5. Attach each Joey mount (if applicable)
C6. Attach power cords to the back of each Joey and the HIC. Do
NOT plug in to power yet
C7. Connect each Joey to its TV
C8. Prepare coax cables; do NOT connect them yet
C9. Clean up all boxes
C10. Clean up inside/outside, including vacuuming
C11. Take tools, supplies and trash back to the vehicle
(D) Configure Remote to TV
D1. Press MENU button
D2. Select "Settings" tile
D3. Select "Remote Manager"
D4. Program TV code
D5. Program Limited Mode
D6. Program other components (DVD player, audio receiver, etc.)
(E) Verify Client ID
Do NOT plug any Joey or HIC to power until the Client ID# populates
E1. From live TV, press the blue shortcut button (Network Setup)
E2. Select the "Tests" tile
E3. Select "View Counters"
E4. Page down to "Client ID"
E5. If the Client ID# is populated, move to Joey setup
E6. If the Client ID# is not populated
a. Put the Hopper in standby
b. Wait 5 minutes and check again
c. Replace the receiver after 3 attempts