Acoustic Energy AEGO3 Panduan Pemilik - Halaman 2
Jelajahi secara online atau unduh pdf Panduan Pemilik untuk Sistem stereo Acoustic Energy AEGO3. Acoustic Energy AEGO3 2 halaman.
SET-UP GUIDE
Thank you for choosing the Acoustic Energy Aego³ music system, please take a moment to
read through this quick set-up guide to ensure correct operation and to get the best
performance from your system.
Whether you've chosen the Sub/Sat or Sub/Soundbar variation of the system, the basic
operation remains the same and performance will be very similar between the two models.
CONNECTION
All physical connections on the Aego³ system are made via the downward- ring panel at
the rear of the subwoofer. This placement ensures tidy cabling and allows for placement
close to walls if necessary.
Left and right speaker outputs:
for connection to individual RCA terminals on
Aego Satellite speakers or L/R inputs on
Soundbar via supplied RCA -> RCA cable.
Stereo Mini-jack input: for use with supplied
3.5mm Mini-jack -> 3.5mm Mini-jack lead
when connecting to audio or headphone
output on sources such as PC, mobile phone,
portable music player, tablet etc.
Power input: for use with supplied power
cable plugged into mains AC outlet.
Optical digital input: for connection to a digital source;
ie - TV, Blu-ray player, Satellite box etc.
TIP: If using multiple sources connected to a TV use the
TV Optical out direct into the Aego³ system rather than
individual connection between di erent sources and
the Aego³. Use PCM Audio output setting on source.
OPERATION
All operation of the Aego³ system is performed via the supplied remote control, there are
no physical controls on the system itself. A brief description of controls is outlined below.
Mute: use to mute system volume,
press again to return volume to last
selected level.
Bass level +: use to increase bass output
from subwoofer between levels 1-4, as
indicated by 1-4 white LED's on Subwoofer
display panel. 1 being minimum and 4
maximum. For most normal use in mid-
sized rooms, levels 2-3 should provide
the best overall balance. Adjust for
personal preference.
Bass level -: use to decrease bass output
from subwoofer between levels 1-4 as
described above.
Dig Input: use to select the Digital input
(Optical) as sound source. This will be
indicated by a white LED on the
Subwoofer display panel.
*Note: If audible distortion is heard
TURN VOLUME DOWN
If the Aego³ is overdriven for sustained
periods protection circuitry will put
the system into standby mode.
Bluetooth®
When selecting the Bluetooth® " " input (indicated by a blue LED on the Subwoofer display panel) for
the rst time, the system will go into "pairing" mode and be visible to Bluetooth®-enabled devices for
connection as "AEGO3". Once paired with the Aego³ the Bluetooth® source device will play audio
wirelessly through the system and operate overall volume level if the function is available.
Whenever the Bluetooth input is selected in future it will attempt to pair with previously connected
devices and become visible to new devices if no previous connections are available. Pairing mode can
also be manually selected by pressing the "Pair" button; when the system is in pairing mode the blue
LED on the Subwoofer display panel will ash, when connection is made the blue LED will remain lit
and an audible "beep" will be heard. The most recently connected device always takes preference
when attempting to play audio.*
*For instructions on source device's Bluetooth® operation please refer to that device's manual or manufacturer.
Power On/O : Once the Aego system
is correctly wired up as described in the
"CONNECTION" section use this button
to switch the system on or place in
"Standby" mode. When in "Standby"
mode a red LED will be lit on the
Subwoofer display panel.
For complete shut-down unplug the
system from the mains power supply.
Volume Up: use to increase volume, as
indicated by 1-4 white LED's on Subwoofer
display panel, when maximum volume is
reached the system will produce an
audible "beep".*
Volume Down: use to decrease volume, as
indicated by 1-4 white LED's on Subwoofer
display panel.
Aux Input: use to select the Aux line-input
(Mini-jack) as sound source. This will be
indicated by an orange LED on the
Subwoofer display panel.