3Doodler Flow Panduan Pengguna - Halaman 8

Jelajahi secara online atau unduh pdf Panduan Pengguna untuk Printer 3D 3Doodler Flow. 3Doodler Flow 9 halaman.

Halaman Cetak

Switching

between

filament types

Do not forget

to snip your

Plastic ends

Reverse and

remove plastic

correctly

Treat your

Nozzle right

Specifications are subject to change and improvement without notice.

SPECIFICATION OF POWER ADAPTER

Input: 100-240V AC, 0.5A MAX, 50-60Hz

Output: +5V DC, 1.2A

CARE & MAINTENANCE

For care and maintenance information, and

more advice on how to use your 3Doodler

Flow, please refer to our website:

the3Doodler.com To troubleshoot, please

visit: the3Doodler.com/troubleshooting

This device complies with Part 15 of the FCC Rules. Operation is subject to the follow-

ing two conditions: (1) this device may not cause harmful interference, and (2) this

device must accept any interference received, including interference that may cause

undesired operation.

Warning: Changes or modifications to this unit not expressly approved by the party

responsible for compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions, may cause harmful

11/2023

• If you're going from ABS to PLA, after clearing as much of the ABS as you can,

insert a spool of PLA and begin extruding while still on the ABS setting. As

soon as you see your new material extruding out, set the temperature to the

proper PLA setting.

• After removing a spool of plastic from the 3Doodler

Flow, cut and discard any partially melted material at the

end of the spool. This will reduce blockages or clogging

issues. Make sure your cut is flat and not angled to

reduce plastic from overlapping in the feed tube.

• DO NOT pull plastic from the back of the 3Doodler Flow

other than as directed.

Light to GREEN/BLUE

Make sure the pen is heated

up and ready to extrude.

TAKE A BREAK:

Give your 3Doodler Flow a rest after every 2 hours of continuous doodling. 30

minutes of down time should be plenty.

• If you ever remove your nozzle, ONLY remove the

nozzle when your pen is heated and a GREEN/BLUE

light is showing. DO NOT remove it when your 3Doodler

Flow is cold.

• If you ever need to tighten your Nozzle, DO NOT force

the Nozzle or overtighten it, as you could break the

Nozzle and permanently damage your 3Doodler Flow.

SPECIFICATIONS

Output Power: 6W

Output Voltage: 5V

Input Voltage: 5V

CARE & MAINTENANCE

For care and maintenance information, and more advice on how to use your

3Doodler, please refer to our website: the3Doodler.com

To troubleshoot, please visit: the3Doodler.com/troubleshooting

LIMITED WARRANTY

For more details on your limited

warranty, please visit:

LIMITED WARRANTY

the3Doodler.com/warranty

For more details on your limited warranty, pleae visit:

For 3Doodler's Terms and Condi-

the3Doodler.com/warranty

tions and other notices please refer

For 3DoodlerÕs Terms and Conditions and other notices please refer to our

website: the3Doodler.com/terms-and-conditions

to our website: the3Doodler.com/

terms-and-conditions

This marking indicates that this product should not be disposed of with

other household wastes. To prevent possible harm to the environment or

human health from uncontrolled waste disposal, recycle it responsibly to

promote the sustainable reuse of material resources.

SECTION 4: TIPS & BEST PRACTICES

Flashing

GREEN/BLUE

Double click either speed

button. The back LED light

will flash to signal plastic is

reversing.

interference to radio communications. However, there is no guarantee that interfer-

ence will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one

or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

- Consult the dealer or an experienced radio/ TV technician for help.

CAN ICES-3 (B)/NMB-3(B)

Snipped Ends

Unsnipped Ends

Once Plastic stops reversing,

it is safe to remove it from the

pen by gently pulling on the

back of the spool.

GREEN/BLUE

Light

This marking indicates that this

product should not be disposed

of with other household wastes.

To prevent possible harm to the

environment or human health

from uncontrolled waste disposal,

recycle it responsibly to promote

the sustainable reuse of material

resources.