esera automation 11134 V2 Panduan Pengguna - Halaman 2
Jelajahi secara online atau unduh pdf Panduan Pengguna untuk Aksesori esera automation 11134 V2. esera automation 11134 V2 7 halaman. Multisensor temperature, humidity and brightness for 1-wire bus system
1
Product description
With the MS 100 1-Wire Multisensor you have purchased a professional Multisensor.
Due to the most modern sensor elements, the accuracy of the MS 100 Multisensor of the rel. humidity
measured values is on average 50% - 100% higher, compared to most sensors on the market.
A Brightness sensor is used to measure the twilight and brightness values within living spaces. A special
photodiode with a human-like detection light spectrum is used.
The MS 100 is installed in a shapely surface-mounted housing and fits harmoniously into modern
furnished living and business rooms.
Thanks to the generous ventilation openings, the 1-Wire Multisensor detects the climate conditions in
rooms very directly and quickly. For all types of radiator and heating controls, an accurate Temperature
sensor such as the one installed in the Multisensor is an important component.
In combination with 1-Wire ESERA Switching modules / binary outputs, a very effective and energy-
saving heating control (single room control) is possible.
The Multisensor is also optimal to warn of possible mold formation.
The MS 100 Multisensor is intended for use in normal living spaces. For outdoor use and in damp rooms,
such as sauna or steam bath, a suitable sensor is available from the ESERA website.
Calibration of the internal sensors is not necessary. The device can be put into operation immediately
without waiting time. The electrical connection to the 1-Wire Bus system of the MS 100 is done with screw
terminals and can be operated in standard mode with 3 cables for ground, data and 5V.
Each MS 100 Multisensor has an individual serial number.
The Multisensor contains an original 1-Wire chip of the type DS2438..
Note
Basics and Tips on the1-Wire Bus system can be found in the ESERA Online Shop under
1-Wire Basics or please refer to our eBook in the Shop under Training/ Documentation
2
Technical data
design
temperature
measuring range,
accuracy
Humidity sensor
design,
measuring range,
accuracy
Brightness sensor
design,
measuring range,
accuracy
Auto-E-Connect
Support
Operating voltage,
current
consumption
Data interface
Protection circuits
connection
All rights reserved. Reproduction as well as electronic duplication of this user guide, complete or in part, requires the written consent of
ESERA GmbH. Errors and technical modification subject to change. ESERA GmbH 2021
www.esera.de
Standard Multisensor for temperature, rel. humidity and brightness.
-30°C to +60°C (sensor element: -55°C to +125°C)
+/- 0,5° in the range from -10°C to + 85°C
capacitive sensor, resolution 9 Bit
0-100%
typical +/-3,5 % (10-85% rF), +/-6% (<10% and >85% rF)
sensor, adapted to the sensitivity of the human eye
approx. 2 - 7000 Lux
+/-25% in the range up to approx. 200 Lux, +/-15% in the range up to 7000
Lux
No support of Auto-E-Connect
5VDC (+/-10%), approx.2mA
1-Wire Bus (5V, data and ground), Original DS2438 Chip
No parasitic operation possible due to reverse polarity and overvoltage
protection
High quality overvoltage protection of the 1-Wire data line up to permanent
28VDC voltage.
Reverse polarity and overvoltage protection for power supply
screw terminal for cable solid 0,2 to 2,5qmm or
fine stranded 0,2 to 1,5qmm
For connection we recommend slotted screwdriver size 2,5x75
11134-V2 V1.0 R1.0 Manual
Page 2 of 7