ACOUSTIC SOLUTIONS SP150 Manual - Halaman 4

Jelajahi secara online atau unduh pdf Manual untuk Jukebox ACOUSTIC SOLUTIONS SP150. ACOUSTIC SOLUTIONS SP150 17 halaman. Cd/hard drive audio jukebox

Halaman Cetak

SET UP INSTRUCTIONS

The SP 150 HD juke box is similar to a conventional CD

player, but has an integral 40Gb hard disc for storage.

It has been designed to be used as part of a Hi Fi system,

and requires connection to an ampliﬁer which accepts

AUX or Line inputs.

The output of the SP150 can be adjusted (described on

page 15), however the default output setting is 280 mV

which is suitable for connection to most domestic Hi Fi

equipment.

POSITIONING THE SP 150

The SP150 is designed to stack within a group of Hi Fi

separates. It does not contain any ventilation grills, so the

proximity of other equipment is not critical, however it is

not advised to cover the SP150 with any material which

might impair its cooling.

The unit can be placed on top of most other pieces of

Hi Fi equipment, however it is our recommendation to

place it on the top of any Hi Fi stack, and try to avoid

placing it directly on top of any high-powered equipment

which may generate excessive heat or electronic radiation,

eg. a power ampliﬁer.

CONNECTION OF AUDIO OUTPUT

Note: Please connect audio output leads ﬁrst before

connecting the mains power to the SP150.

The SP150 is ﬁtted with two RCA phono jacks which deliver

line level audio signals to a suitable ampliﬁer. Using the

lead supplied take one end and push both the white and

red RCA plugs into the corresponding sockets located on

the rear of the SP150.

Ensuring that no twists or kinks are apparent, or that the

cable has been damaged in any way, take the other end

of this cable and push the RCA plugs in to corresponding

input sockets on the rear of your ampliﬁer.

Please ensure that you have connected the SP150

to corresponding line input sockets, and not a phono

(turntable) input sockets. This would cause the phono

sockets to become overloaded.

CONNECTION OF MAINS POWER

The SP150 is ﬁtted with a mains power plug which is

applicable to your worldwide location.

Note: if the power plug ﬁtted to the SP150 does not

match the power sockets used in your worldwide

location, please consult your dealer for further

information.

The SP150 is ﬁtted with a self regulating power supply

and will automatically adjust to the voltage setting in your

region.

page 4

Please ensure that the power lead is free from damage,

and has not been twisted or kinked.

If the power cable ﬁtted to the SP150 is damaged in any

way, please do not connect to a mains power supply, but

return the unit to your dealer for a replacement product.

If your mains power outlet is switched, ensure the power

is switched off and then connect the SP150 to the mains

power supply pushing the plug ﬁrmly into the socket. Then

turn the power switch on the mains power outlet to on.

TURNING THE POWER ON/OFF

The power button on the SP150 is located on the far right

of the front panel. Located next to the power switch is an

LED (light emitting diode) which indicates that the power is

ON when it is green. The LCD screen will also illuminate

and has a green-yellow background light.

To turn ON the SP150, depress the power switch until you

hear and feel a positive click. At this time the LED will be

green.

To turn the SP150 OFF, simply reverse the process above,

the LED will also go off.

Note: It is safe to leave the SP150 connected to the mains

power supply for a reasonable length of time, however as

with most electrical equipment, you would be advised to

remove connection to the mains power supply if the unit

was going to be left unattended to considerable lengths

of time.

STANDBY POWER SETTING

The SP150 has a standby power setting which can only be

operated by the remote control by pressing button 7.

The SP150 has been designed to offer automatic ﬁle

compression as a default factory setting. This means that

the ﬁle compression process will take place without the

need for compression programs that would be necessary

when using a computer.

It is necessary for the SP150 to be placed in standby mode

periodically as ﬁle compression is a process which occurs

automatically whilst in standby mode or can be controlled on

manually from the system menu (see advanced functions

page 14 for further information on ﬁle compression)

Press the standby button on the remote control to place

the SP150 in standby mode, and ﬁle compression will

start. If you press the standby button on the remote control

again within 5 seconds the ﬁle compression process will

cease and the SP150 will revert to standby without ﬁle

compression. If after 5 seconds, if you press the standby

button again, the SP150 will resume normal function.