Akiyama Quark Panduan Pengguna - Halaman 11

Jelajahi secara online atau unduh pdf Panduan Pengguna untuk Peralatan Perekaman Akiyama Quark. Akiyama Quark 20 halaman. Pro dj midi controller
Juga untuk Akiyama Quark: Panduan Pengguna (20 halaman)

Halaman Cetak

Quark. User Manual

-Press any cue buttons, which have a cue point stored, to

trigger the stored cue.

-Hot cues can be deleted by pressing the cue button while

holding the button labelled with a bin.

-Press SHIFT + HOT CUE 1 to activate/deactivate Smart Hot

Cue.

-A yellow lit button means that there is a hot cue saved.

AUTO LOOP (round button orange):

-An autoloop is set by pressing any of the 6 numbered buttons.

The autoloop size depends on the pressed button and can be

set from 1 to 32 beats.

-The autoloop is deactivated by pressing the button

corresponding to the actual size.

-Change the loop size by pressing a button which has

associated a size different than the actual active loop size.

-Press SHIFT + HOT CUE 1 to activate/deactivate Smart

Loop.

-In this mode all buttons will light orange. The button

corresponding to the active loop size will blink.

LOOP ROLL (round button green):

-An autoloop is set by pressing any of the 6 numbered buttons.

The autoloop size depends on the pressed button and can be

set from 1/32 to 1 beat. The loop will be active only while the

button is hold.

-Press SHIFT + HOT CUE 1 to activate/deactivate Smart

Loop.

-In this mode all buttons will light green. The button

corresponding to the active loop size will blink.

4. DECK SELECT

Switch between decks A/C and decks B/D.

5. LOOP

-Set the starting point of a loop by pressing IN button.

-Press OUT button to set the ending point of the loop.

-Press RELOOP to jump to the starting point of the loop. If loop

is not activated, the last set loop will be activated.

-Press SHIFT + IN to enter in a mode in which the starting

point of the loop can be modified, IN ADJUST. The IN button

will blink while this mode is active. Turn the jog wheel to modify

the starting point. Press SHIFT + IN to exit from the mode. If

this mode is active but there is not any loop active, the last set

loop will be activated when the jog wheel is turned.

-Press SHIFT + OUT to enter in a mode in which the ending

point of the loop can be modified, OUT ADJUST. The

performance of this mode is equivalent to the IN ADJUST

mode but in this case the ending point is adjusted.

-Enter to MOVE LOOP mode by pressing SHIFT + RELOOP.

Performance is similar to IN/OUT ADJUST but in this case

loop can be moved..

6. JOGWHEEL

Press SCRATCH button to toggle the wheel mode between

CDJ and Vinyl.

-Use the jog wheel to scratch or modify the pitch bend.

-Use SHIFT + jog wheel to search through the track

-Under Video mode press SHIFT + turn jog wheel to adjust the

parameter of the effect

7. TEMPO

-Use the Pitch Fader to control the deck's tempo.

-Use the Pitch Bend buttons for pitch bending.

-Tempo Range can be selected by pressing SHIFT + pitch

bend (-).

-Reset the tempo by pressing SHIFT + pitch bend (+).

8. TRANSPORT

-Press Play/Pause button to Start/Stop playback of deck.

-Press SHIFT + Play/Pause to skip to the first beat of the track.

-If song is paused, set a new cue point or if you are in the cue

point position play the track from the cue point by pressing the

CUE button and return to cue point when released. If song is

playing, press CUE to pause the reproduction and jump to the

last cue point.

-Use SHIFT + CUE to activate/deactivate Smart Play.

-Use the SYNC button to match the BPMs of different tracks.

-Press SHIFT + SYNC to set to master the deck in which it has

been pressed.

9. MIXER

-Tweak the sound using the 3-Band EQ

-Turn the MASTER knob to adjust the volume of the master

signal.

-Adjust the deck volume by turning the gain knob.

-Select the deck that must be pre-listened by pressing the

Monitor buttons (labelled with headphones).

-Press SHIFT + Monitor button to select the beat of the

working deck which will be shown in front in the display.

-Use the Linefader and Crossfader for mixing.

-Use AUTO buttons to automatically crossfader to the other

deck.

-Under Video mode press LINK to link or unlink the video

crossfader to the audio crossfader.

-Under Video mode use AUTO to move the video crossfader

automatically.

10. BROWSER

-Turn the encoder to scroll through the songs.

-Press SHIFT + turn the encoder to scroll through the folders.

-Load the song to the active deck by pressing LOAD buttons.

-Press the encoder to open or close the subfolders of the

selected folder (when focus is on folders).

-Press SHIFT + encoder to open or close the subfolders of the

selected folder (when focus is on folders).

-Switch the mixer section between mixer and video by pushing

VIDEO MODE.