ARTFOX Lighting LED Spot 150W RGBW Quad Panduan Pengguna - Halaman 7

Jelajahi secara online atau unduh pdf Panduan Pengguna untuk Lampu Banjir ARTFOX Lighting LED Spot 150W RGBW Quad. ARTFOX Lighting LED Spot 150W RGBW Quad 8 halaman. Led moving head

Halaman Cetak
POWER SUPPLY-MAINS
Connect the power cord as follows:
L (live) =brown
E (earth) =yellow/green
N (neutral) =blue
Use the plug provided to connect the mains power to the projector paying attention to the
voltage and frequency marked on the panel of the projector. It is recommended that each
projector be supplied separately so that they may be individually switched on and off.
IMPORTANT
It is essential that each projector is correctly earthed and the electrical installation conforms to all
relevant standards.

CONTROL CONNECTION

CONTROL CONNECTION
DMX OUT
2
3PIN
3
DMX OUT
5
5PIN
4
3
Connection between controller and projector and between one projector and another must be
made with a 2 core-screened cable, with each core having at least a 0.5mm diameter.
Connection to and from the projector is via cannon 5 pin (which are included with the projector)
or 3 pin XLR plugs and sockets. The XLR's are connected as shown in the gure above.
Note: care should be taken to ensure that none of the pins touch the metallic body of the plug or
each other. The body of the plug is not connected in any way. The projector accepts digital
control signals in protocol DMX512 (1990).
Connect the controller's output to the rst xture's input, and connect the rst xture's output to
the second xture's input and connect the rest xtures in the same way. Eventually connect the
last xture's output to a DMX terminator as shown in the gure below.
120 Ohms
DMX IN
1
1
2
PIN
1
2
3
3
DMX IN
PIN
1
5
1
1
2
3
4
2
2
4
5
3
DMX512
DMX-controller
4

MAINTENANCE

To prolong a Projector's life, Regular maintenance should be done for its LED optical System
to ensure that the system be in best operational condition. If the projector does not
function, check the fuses on the power socket of the projector, if burned, they should only
be replaced by fuses of the same specication. Should these be damaged call a qualied
technician before replacement. The projector has thermal protection device that will
switch off the projector in case of overheating, should this occur, check if the fans work
normally or fan and fan shield are blocked by dust. If the projector not operational, call a
qualied technician. After cleaned and repaired, the projector can be restarted.
Any maintenance work should only be carried out by qualied technicians.
KEEPING THE PROJECTOR CLEAN
It denitely necessary to keep a projector clean for its reliable use. Cooling fans and their
DMX512
shield should be cleaned every 15days. LED lamps'lens and cover should be cleaned
FUNCTION
regularly for optimized light output.
GND
DATA-
DATA+
Cleaning frequency depends on how often a projector is used and its operational
environment. A soft cloth and typical glass cleaning products should be used in cleaning.
It is recommended to clean the external optics at least once every 20 days.
DMX512
FUNCTION
GND
DATA-
DATA+
Do not use any organic solvent, e.g. alcohol, to clean t housing of the apparatus.
N/C
N/C

TROUBLESHOOTING

PROBLEM
The xture can not start
The lamp works normal but the
xture doesn't respond to
controller
The xture only functions
intermittently
The beam appears dim and
brightness decreases apparently
ACTION
> Check if the fuse on the power socket is broken or not.
> Check the status of the fuse.
> Check if the xture's start address is set properly.
> Check if XLR signal cable is broken or not.
> Make sure the fans work normally and if dirt blocks
fans and fan screens.
> Check if the lamps reach the end of their lives.
> Check if external and internal optical systems are
clean or not.
13