Altrocraft 241-9847 Panduan Operator - Halaman 3

Jelajahi secara online atau unduh pdf Panduan Operator untuk Melihat Altrocraft 241-9847. Altrocraft 241-9847 9 halaman. 6.0 amp

Halaman Cetak

SAFETY PRECAUTIONS FOR RECIPROCATING SAW

IMPORTANT SAFETY INSTRUCTIONS

15. USE EYE PROTECTION. Use a full-face mask if the work you're doing

produces metal ﬁlings, dust or wood chips. Goggles are acceptable in other

situations. Wear a clean dust mask if the work involves creating a lot of ﬁne

or coarse dust.

16. SECURE WORK. Use clamps or a vise to hold the work. It's safer than using

your hands and it frees both hands to operate the tool.

17. DON'T OVERREACH. Keep proper footing and balance at all times. Do not

reach over or across machines that are running.

18. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and

safer performance. Follow instructions for lubricating and changing accessories.

For safe performance,Keep handles dry, clean and free from oil and grease.

19. AVOID UNINTENTIONAL STARTING. Be sure the switch is in the OFF posi-

tion before plugging in.

20. ALWAYS CHECK AND MAKE SURE TO REMOVE ANY ADJUSTING KEYS

OR WRENCHES before turning the tool on. Left attached, these parts can ﬂy

off a moving part and result in personal injury.

21. DO NOT USE THE TOOL IF IT CANNOT BE SWITCHED ON OR OFF.

Have your tool repaired before using it.

22. DISCONNECT THE PLUG FROM POWER BEFORE MAKING ANY AD -

JUSTMENTS. Changing attachments or accessories can be dangerous if

the tool could accidentally start.

23. STAY ALERT. Watch what you are doing & use common sense. Don't operate

any tool when you are tired.

24. CHECK FOR DAMAGED PARTS. Before using this tool, any part that is

damaged should be carefully checked to determine that it will operate prop-

erly and perform its intended function. Check for alignment of moving parts,

binding of moving parts, breakage of parts, mountings, and other conditions

that may affect its operation. Inspect screws and tighten any ones that are

loose. Any part that is damaged should be properly repaired or replaced by

an authorized service center unless otherwise indicated elsewhere in the in-

struction manual. Have defective switches replaced by an authorized service

center. Don't use the tool if switch does not turn it on and off properly.

25. REPLACEMENT PARTS. When servicing, use only identical replacement

parts.

26. SERVICE AND REPAIRS should be made by qualiﬁed repair technicians at

an authorized repair center. Improperly repaired tools could cause serious

shock or injury

1. GUARD AGAINST ELECTRIC SHOCK. When cutting wherever "live" electri-

cal wires may be encountered, hold the tool only by the plastic handle and

the rubber grip at the front of the tool to prevent electric shock. DO NOT

TOUCH ANY METAL PARTS OF THE TOOL. If you contact a live wire, the

exposed metal of the saw becomes live as well, and can cause a severe shock

to the operater.

Before switching on the tool, be sure the blade is not contacting the work piece.

DO NOT START THE SAW WITH THE BLADE IN CONTACT WITH ANY

SURFACE. The reciprocating action will cause the saw to bounce violently

and could cause injury.

LET THE SAW COME TO A STOP before putting it down. The reciprocat-

ing action could cause the saw to jerk violently if the blade comes in contact

with any objects.

Always wear safety glasses or goggles, normal prescription eye or sunglasses

are not safety glasses.

Do not cut nails or screws unless you are using a blade specifically designed

for this purpose, Inspect your material before cutting.

WARNING: The warnings, cautions, and instructions detailed in this manual

cannot cover all possible conditions and situations that occur. It must be

understood by the operator that COMMON SENSE AND CAUTION ARE

FACTORS that cannot be built into this product, but MUST BE SUPPLIED

BY THE OPERATOR.