Arthrex Synergy Resection Panduan Memulai Cepat - Halaman 2

Jelajahi secara online atau unduh pdf Panduan Memulai Cepat untuk Beralih Arthrex Synergy Resection. Arthrex Synergy Resection 2 halaman. Wireless footswitch

Halaman Cetak
Troubleshooting: Faults and Solutions
Fault
Handpiece does not operate after pressing a pedal, but the
pedal indicator illuminates on the receiver
Handpiece does not operate after pressing the pedal and
the pedal indicator does not illuminate on the receiver
If the footswitch has a low battery, the battery LED will turn RED. At this time, you will need to replace the batteries and press a button or
pedal on the footswitch to clear the warning light. It is not necessary to pair the footswitch with the receiver again.
to
Red light will remain on when there is a low battery. From the time the red light appears, the battery will die within 10 hours.
1
2
Button Activation Receiver
Pic.
Name
1
Green Power
ON Indicator
2
White Direction
ON Indicator
3
RED Battery/
Status LED
Indicator
4
Pairing Button
This description of technique is provided as an educational tool and clinical aid to assist properly licensed medical professionals
in the usage of specific Arthrex products. As part of this professional usage, the medical professional must use their professional
judgment in making any final determinations in product usage and technique. In doing so, the medical professional should rely on
their own training and experience and should conduct a thorough review of pertinent medical literature and the product's directions
for use. Postoperative management is patient-specific and dependent on the treating professional's assessment. Individual results
will vary and not all patients will experience the same postoperative activity level or outcomes.
www.arthrex.com
© 2019 Arthrex, Inc. All rights reserved. LI1-000009-en-US_A
3
4
Description
On when there is connection to the
console.
Left LED ON When REVERSE Pedal is ON.
Right LED ON When FORWARD Pedal is
ON. Top Middle LED ON When OSCILLATE
Pedal is Pressed.
• Off – It is paired with a footswitch with
good battery level
• Flashing Slowly (50% duty cycle @
1 Hz) – It is not paired with any footswitch
• Flashing Rapidly – Pairing in process
• Solid Red – Footswitch has low (<=2.0V)
battery
Pushbutton behind the wireless symbol.
Press and hold until RED Battery/Status
LED begins to flash rapidly to start the
pairing process. Refer to the Transmitter/
Receiver pairing section of this manual.
Solution
1. Ensure that the battery warning indicator is not illuminated. If it is, replace the
batteries within the footswitch.
2. If the battery warning indicator is not illuminated, check to make sure the
handpiece is fully plugged into the console and that there are no error messages
on the console display screen.
3. Try plugging the handpiece and the receiver into a different port on the console.
If this does not resolve the issue, try a new shaver handpiece.
1. Make sure receiver is fully plugged into the console and that the green power
indicator is lit. If it is, make sure nothing is covering the receiver.
2. Try pairing the footswitch again and make sure there are fresh batteries in the
correct direction within the footswitch.
8
12
5
Footswitch Transmitter
Pic.
Name
5
Left Pedal
6
Center Pedal
7
Right Pedal
8
TOGGLE
9
GFS Cruise/SFS
Speed Button
10
SFS/GFS Mode
Button
11
Pairing Pushbutton
12
Battery Tube
Arthrex, Inc.
1370 Creekside Blvd.
Naples, FL 34108-1945 USA
Toll-Free: 1 (800) 934-4404
www.arthrex.com
Tech Support: +1-888-420-9393
10
11
9
6
Description
Reverse
Oscillate
Forward
Pushbutton
In SFS Mode, button will change the Speed.
In GFS Mode, button will set Cruise Control.
SFS/GFS Mode Pushbutton – Switches
between GFS (gas pedal footswitch)
mode and SFS (standard footswitch)
mode. (Pedal must be flat)
Arthrex GmbH
Erwin-Hielscher-Strasse 9
81249 München, Germany
Tel: +49 89 909005-0
www.arthrex.de
Tech Support: +49 89 90 90 05 8800
7