dji Inspire 1 Pro Panduan Memulai Cepat - Halaman 9

Jelajahi secara online atau unduh pdf Panduan Memulai Cepat untuk Drone dji Inspire 1 Pro. dji Inspire 1 Pro 10 halaman.
Juga untuk dji Inspire 1 Pro: Panduan Memulai Cepat (11 halaman), Panduan Memulai Cepat (11 halaman), Panduan Pengguna (10 halaman)

Halaman Cetak

11. Flight

Safe to Fly (GPS)

Before taking off, make sure the aircraft

status bar in the DJI GO app shows "Safe

to Fly (GPS)". Otherwise, the aircraft cannot

hover in place and record the Home Point.

Manual Take - off & Landing

Start the motors by pulling both control sticks to the bottom inside (or outside)

corners. Release the sticks once the motors start. Slowly push the left (throttle)

stick up to take off. Once in the air, toggle the Transformation Switch up to

raise the landing gear.

Start / Stop the motors

Gently pull the left (throttle) stick down to lower the

aircraft until it touches the ground. Pull both sticks to the

bottom inside corners to stop the motors.

After flight, change the aircraft back into Travel Mode. Do

not attempt this at the beach, over grass, or over

monochromatic carpet. Then place the aircraft on a flat

surface and remove the gimbal and camera for transport.

It is highly recommended that you only take off when the Aircraft Status bar is green.

The aircraft cannot take off if the Critical Low Battery Warning is active.

The Intelligent Flight Battery must warm-up if the outside temperature is low. A warning will

display in the DJI GO app.

Rotating propellers can be dangerous. Do not start the motors when there are people nearby

and always fly in a wide open area.

Never stop the motors during flight. Always keep your hands on the remote controller so long as

the motor is still spinning. Power off the aircraft before turning off the remote controller after landing.

Appendix

Aircraft

Status Indicator Description

Slowly: Safe to fly,GPS working

Double: Vision Positioning

System working, no GPS

Slowly: P-ATTI or ATTI

Quickly: Not connected

to remote controller

Slowly: Low battery level warning

Quickly: Critical low battery level warning

Solid: Critical error

Blinking Alternately:

Compass calibration required

Auto Taking - Off & Landing:

( In the Camera screen of the DJI GO app )

Tap

and confirm your selection. The aircraft will automatically take off, retract its

landing gear, and hover at 1.2 meters after you tap and confirm Auto Take-off.

Tap

and confirm your selection. The landing gear will lower and the aircraft will

automatically land.

Left stick / Up (Slowly)

Left stick / Down (Slowly)

Remote Controller Status LED

RC normal but not connected to aircraft.

RC normal and connected to aircraft.

RC Slave Mode and not connected to aircraft.

RC Slave Mode and connected to aircraft.

B-B-B... Aircraft low battery warning /

RC error.

B—B—... RC idle for 5 minutes.

Video downlink error.

Initiate RTH procedure.

B... Send RTH command to aircraft.

BB .. .. Aircraft returning to Home Point.

Learn more information from:

www.dji.com/product/inspire-1-pro-and-raw

Return to Home

Toggle the

Transformation

RTH Button

Switch up

1. Press and hold the return home

button until the LED surrounding the

button is blinking white, and the

return home procedure is in process.

Press once to stop the procedure.

2. The DJI GO app notifies users to take

action when the battery level falls to a

specified threshold. This warning

threshold can be set within the DJI

GO app. The aircraft will land

immediately when it reaches Critical

Low Battery Level Warning.

3. Failsafe: The Inspire 1 Pro will enter

RTH mode if remote controller signal

is lost.

Using the Camera

Adjust the camera parameters using the

Camera Settings Dial on the remote controller

or through the DJI GO app. Press the Shutter

Button/Video Record Button to capture

photos or record videos.

Adjust the tilt of the gimbal using the Gimbal

Dial.

Download photos and video from the SD card

to your mobile device through the DJI GO

app. You may also use a SD card reader to

export files to your PC.

The App's

RTH Button