djm direct DJMSL10 Terjemahan Manual Pengoperasian Asli - Halaman 7
Jelajahi secara online atau unduh pdf Terjemahan Manual Pengoperasian Asli untuk Melihat djm direct DJMSL10. djm direct DJMSL10 14 halaman. 10 single bevel compound sliding mitle saw
Halaman Cetak
9. Operating
Avoid unintentional starting of the machine. During assembly and for
all work on the machine, the power plug must not be connected to
the mains supply.
Carefully remove all parts included in the delivery from their
packaging.
Remove all packaging material from the machine and the accessories
provided.
Before starting the operation of the machine for the first time, check
if all parts listed in the box content section have been supplied
Note: Check the power tool for possible damage. Before further use
of the machine, check that all protective devices are fully functional.
Any lightly damaged parts must be carefully checked to ensure
flawless operation of the tool. All parts must be properly mounted
and all conditions fulfilled that ensure faultless operation.
Damaged protective devices and parts must be immediately replaced
by an authorised service centre.
Bench Mounting
The saw base has holes in each corner to facilitate bench mounting.
1. Place the saw on a level, horizontal bench or work table using bolts
(not supplied) and fix the saw to the bench using 4 bolts.
2. If desired, you can mount the saw to a piece of 1/2" (13 mm) or
thicker plywood which can then be clamped to your work support or
moved to other job sites and re-clamped.
CAUTION. Make sure that the mounting surface is not warped as an
uneven surface can cause binding and inaccurate sawing.
Release knob
The release knob (2) is provided for holding the cutting head down
while transporting or storing the mitre saw. The saw must never be
used with the release knob locking the head down.
Mitre table locks
The mitre table locks (18) are used to lock the table at the desired
mitre angle.
The mitre saw cuts from 0° to 45° both left and right. To adjust the
mitre angle loosen the mitre table locks(18)(19) and rotate the mitre
table to the desired position.
The mitre table features positive click stops at 0°, 15°, 22.5°, 30° and
45° for quick setting of common mitre angles.
Bevel lock
The bevel lock (10) is used to set the blade at the desired bevel angle.
The mitre saw bevel cuts from 0° to 45° to the left. To adjust the
bevel angle loosen the bevel lock and adjust the saw arm to the
desired bevel angle.
Spindle lock button
The spindle lock button (20) prevents the blade in the saw from
rotating. Depress and hold the spindle lock button while installing,
changing, or removing the blade.
Rotating lower blade guard
The rotating lower blade guard (6) provides protection from both
sides of the blade. It retracts over the upper blade guard (4) as the
saw is lowered into the workpiece.
Turning on and off
1. To turn the saw on depress and hold the on/off trigger switch (17)
2. To turn the saw off release the on/off trigger switch (17).
Dust extraction
1. Fit the dust bag (9) to the dust extraction port.
2. A vacuum dust extraction device can be connected to the dust
extraction port. Use a suitable vacuum adaptor if necessary. The dust
extraction port has an internal diameter of 40 mm.
Setting the table square with the blade
1. Make sure that the electrical plug is removed from the power
point.
2. Push the saw arm (1) down to its lowest position and engage the
release knob (2) to hold the saw arm in the transport position.
3. Loosen the mitre locks (18) and lifting up the mitre latch(19) .
4. Rotate the table (14) until the pointer is positioned at 0°.
5. Release mitre latch(19) and tighten the mitre locks (18).
6. Loosen the bevel lock (10) and set the saw arm (1) at 0°bevel
(the blade at 90°to the mitre table). Tighten the bevel lock (10).
7. Place a set square against the table (14) and the flat part of the
blade.
8. Rotate the blade by hand and check the blade-to-table alignment
at several points.
9. The edge of the set square and the saw blade should be parallel.
10. If the saw blade angles away from the set square, adjust as
follows.
11. Use an 10 mm wrench or adjustable wrench to loosen the lock
nut securing the 0° bevel adjustment screw (27). Also, loosen the
bevel lock (10).
12. Adjust the 0° bevel adjustment screw (27) using a 4 mm hex key
to bring the saw blade into alignment with the square.
13. Loosen the Phillips head screw holding the pointer of the bevel
scale (11) and adjust the position of the pointer so that it accurately
indicates zero on the scale. Retighten the screw.
14. Retighten the bevel lock (10) and the lock nut securing the 0°
bevel adjustment screw (27).
6