djm direct DJMSL8 Terjemahan Manual Pengoperasian Asli - Halaman 6
Jelajahi secara online atau unduh pdf Terjemahan Manual Pengoperasian Asli untuk Melihat djm direct DJMSL8. djm direct DJMSL8 14 halaman.
Halaman Cetak
· Rags, cloths, cord and string and the like should never be left
around the work area.
· Avoid cutting nails. Inspect the workpiece and remove all nails and
other foreign objects before beginning sawing.
· Support the work properly.
· Refrain from removing any cut-offs or other parts of the workpiece
from the cutting area whilst the machine is running and the saw head
is not in the rest position or whilst the machine is running with an
unguarded saw blade.
· Do not attempt to free a jammed blade before first switching off
the machine.
· Do not slow or stop a blade with a piece of wood. Let the blade
come to rest naturally.
· If you are interrupted when operating the saw, complete the
process and switch off before looking up.
· Periodically check that all nuts, bolts and other fixings are properly
tightened.
· Do not store materials or equipment above a machine in such a
way that they could fall into it.
· Always hold the saw on parts that are insulated. If you accidentally
cut into hidden wiring or the saw's own cable, the metal parts of the
saw will become "live". Switch off at the mains and remove the plug
immediately.
· Never saw near combustible liquids or gases. · Note the direction
of rotation of the motor and the blade.
· Do not lock the movable guard in the open position and always
ensure that it is working properly, freely rotating and returning to
fully cover the teeth of the blade.
· Connect the saw to a dust collection devise and ensure that it is
operated properly. As the operator of the saw, please make sure that
you understand factors that influence exposure to dust, including the
type of material to be machined, the importance of local extraction
and the proper adjustment of hoods/baffles/ shoots of your dust
extraction system. We recommend that you always wear a dust mask
when operating this saw. ·
· Wear gloves when handling saw blades and rough materials. · Saw
blades shall be carried in a holder wherever possible.
· Select saw blades in relation to the material being cut. ·
· Use correctly sharpened saw blades and observe the maximum
speed marked on the blade. Ensure the speed marked on the saw
blade is at least equal to the speed marked on the saw ·
· Take additional care when trenching (slotting).
· The mitre saw can be safely carried by the carrying handle but only
once it has been removed from the mains power and secured in the
locked down position. Warning! Never use the guard as the lifting
and transportation purpose!
· Ensure that the arm is properly secure when bevelling.
· Keep the floor area around the machine level, well maintained and
free of loose materials.
· Ensure that you are trained in the use,adjustment and operation of
the machine.
· Do not remove any cut-offs from the cutting area until the guard is
fully locked in placed and the blade has come to rest.
· Where possible use clamps or a vice to hold the workpieces. It is
safer than using your hand.
· before each cut, make sure that the machine is stable.
· When cutting long pieces which extend well over the table width,
ensure that the ends are adequately supported at the same height as
the saw table top. Supports should be positioned in such a way to
ensure that the workpiece does not fall to the ground once the cut
has been made. A number of supports at regular intervals may be
required if the workpiece is extremely long.
· During slide cutting, always ensure that the saw blade is pushed
away from the operator.
· Always use stands to provide support for long work pieces that
overhang the turntable.
· Feed work into a blade or cutter against the direction of rotation of
the blade or cutter only.
· Before making compound mitre cuts, ensure that the work head is
securely fixed in the desired position.
· Never reach over the blade to remove waste or off cuts.
8. Technical Data
Specifications:
Mains Voltage - 230V/ 50Hz
Power Consumption - 1500W
No load Speed - 5500rpm
Blade Spec - 210x30x24T
Cutting Capacity:
At 0° / 0°- 210x70mm
At 45° / 0° - 147x70mm
At 0° / 45°- 210x35mm
At 45° / 45°- 147x35mm
9. Operating
Avoid unintentional starting of the machine. During assembly and for
all work on the machine, the power plug must not be connected to
the mains supply.
Carefully remove all parts included in the delivery from their
packaging.
5