Altronix AL1002ULADAJ Manual Aplikasi - Halaman 5

Jelajahi secara online atau unduh pdf Manual Aplikasi untuk Pemanjang Altronix AL1002ULADAJ. Altronix AL1002ULADAJ 8 halaman. Nac power extenders
Juga untuk Altronix AL1002ULADAJ: Panduan Instalasi (17 halaman), Manual Aplikasi (8 halaman), Manual Aplikasi (8 halaman)

Halaman Cetak

Function

Input to Output

Follower Mode

Temporal Code 3 Mode

Steady Mode

For the above modes DIP Switch 4 determines which Input controls the

corresponding output:

Switch 4 in the ON position causes output(s) to be controlled by Input 1.

Switch 4 in the OFF position causes output(s) to be controlled by Input 2.

Function

Amseco

Sync Mode*

Faraday

Sync Mode*

Gentex

Sync Mode*

Gentex is a registered

trademark of

Gentex Corporation.

System Sensor

Sync Mode*

System Sensor is a

registered trademark of

Honeywell.

CooperWheelock

Sync Mode*

CooperWheelock is a

registered trademark of

Cooper Wheelock.

*Note: The AL602ULADA, AL602ULADAJ, AL802ULADA, AL802ULADAJ, AL1002ULADA and

AL1002ULADAJ will only synchronize horns, horn/strobes and strobes that contain synchronization capability.

Contact signal manufacturer for more detailed info.

The same synchronization mode must be selected for all outputs.

02 ULADA Application Guide

Output Programming Selection Table:

Outputs must be programmed independently (OUT1 - OUT4)

Switch Positions

OFF

2, 3

1, 2

1, 2, 3

Sync Mode Selection Table:

Switch Positions

OFF

1, 3,

2, 4

1, 3

1, 2,

3, 4

1, 2, 4

2, 3, 4

Descriptions

Output follows signal it receives from the corresponding

input (i.e. FACP Sync module - maintains synchronization

of notification appliance circuit).

Enables Temporal Code 3 signal generation output.

This mode will accept a steady or a pulsing input.

A steady output signal will be generated.

This mode will accept steady or pulsing input.

Descriptions

This mode is designed to work with the Amseco series of horns,

strobes, and horn/strobes to provide a means of synchronizing

the Temporal-coded horns, synchronizing the flash timing of the

strobe, and silencing the horns of the horn/strobe combination over

a two-wire circuit while leaving strobes active.

This mode is designed to work with the Faraday series of horns,

strobes, and horn/strobes to provide a means of synchronizing the

Temporal-coded horns, synchronizing the flash timing of the strobe,

and silencing the horns of the horn/strobe combination over a two-

wire circuit while leaving strobes active.

This mode is designed to work with the Gentex

strobes, and horn/strobes to provide a means of synchronizing

the Temporal-coded horns, synchronizing the flash timing of the

strobe, and silencing the horns of the horn/strobe combination

over a two-wire circuit while leaving strobes active.

This mode is designed to work with the System Sensor

horns, strobes, and horn/strobes to provide a means of synchroniz-

ing the Temporal-coded horns, synchronizing the one-second flash

timing of the strobe, and silencing the horns of the horn/strobe

combination over a two-wire circuit while leaving strobes active.

This mode is designed to work with the CooperWheelock series of

horns, strobes, and horn/strobes to provide a means of synchronizing

the Temporal-coded horns, synchronizing the one-second flash tim-

ing of the strobe, and silencing the horns of the horn/strobe combina-

tion over a two-wire circuit while leaving strobes active.

AL800LGK9E Board

Output DIP Switches

INPUT SELECT

TEMPORAL

STROBE SYNC

IN>OUT SYNC

series of horns,

series of

- 5 -