AKO K 821 Panduan Petunjuk Pemasangan dan Pengoperasian - Halaman 4
Jelajahi secara online atau unduh pdf Panduan Petunjuk Pemasangan dan Pengoperasian untuk Pemanas AKO K 821. AKO K 821 12 halaman.
EN
4. Electrical Connection
The voltage specified on the type plate must match the local
mains voltage.
If the power cord of this device is damaged, it must be replaced
by the manufacturer or after-sales service, or else by a similarly
qualified person, in order to prevent risks.
The device plug must always be accessible.
In order to avoid a hazard due to inadvertent resetting of the
thermal cut-out, this appliance must not be supplied through an
external switching device, such as a timer, or connected to a
circuit that is regularly switched on and off by the utility.
5. Operation
The room temperature is regulated using the infinitely
adjustable thermostat (C). If the rotary knob is set to the lowest
setting i.e. to the extreme left (see figure), the thermostat
switches the heating device on at an ambient temperature of
approx. 5°C.
The heating device is switched on and off using the power
switch (D).
Two heating levels (I = 1000W or II = 2000W) can be selected
using the operating mode switch (E).
The red light illuminates when the device is in heating
operation.
Note!
Rooms can become overheated if left unattended whilst being
heated; this depends on the size of the room, its heating
requirements and the setting of the thermostat. Persons who
are not able to vacate the room if the temperature becomes too
high can thus be placed in danger.
5.1 Fan operation (device type K 821 only)
Switch F switches on a fan which causes faster heat
distribution through increased air recirculation.
The fan can also be used as cold air fan.
In cold air fan operation, turn the thermostat rotary knob to the
maximum (clockwise).
6. Protection Against Overheating
If the permissible temperature is exceeded, the heating device
switches off automatically. If this occurs, pull the mains plug out
and leave the device unplugged for a few minutes, so that the
temperature limiter can switch back again.
Then remove the cause e.g. when the air grid is blocked or
covered. When the device has cooled sufficiently, it can be
started up again.
7. Faults
If the heating device does not give off heat, check the following
points:
• Is the power switch (B) in the ON position?
• Has the thermostat been set to the desired temperature?
• Has the overheat protection been triggered? See chapter 6!
• Is the fuse in the fuse box switched on?
If you cannot remedy the fault, please contact your electrical
retailer. If required, you can also address your queries to the
service hotline of Glen Dimplex Deutschland GmbH.
Tel.: +49 (0) 9221 709-564
Fax: +49 (0) 9221 709-589
To process your order, please state the device type as well as
its production number (E Nr.) and manufacturing date (FD).
This information is listed on the type plate.
Repairs and corrective measures may only be carried out by a
qualified electrician or by your after-sales service.
8. Cleaning
To clean the device, first disconnect it from the mains and allow
it to cool down. Clean the outside of the unit using a soft, damp
cloth. Do not use scouring powder or furniture polish as this
may damage the surface. Dust which gathers inside the device
can be removed from the outside using a vacuum cleaner.
9. Warranty
This product is supplied with a two-year warranty according to
our terms of guarantee.
10. Note on Disposal
Do not dispose of the unit with general household
waste. The device must be taken to a local waste
disposal plant.
Glen Dimplex Deutschland GmbH
Am Goldenen Feld 18, D-95326 Kulmbach
www.glendimplex.de
kundendienst.hauswaerme@glendimplex.de
4
k811-gb_ba 02/09/C