Blue Angel BSE50 Petunjuk Pengoperasian dan Manual Suku Cadang - Halaman 3

Jelajahi secara online atau unduh pdf Petunjuk Pengoperasian dan Manual Suku Cadang untuk Pompa Daya Blue Angel BSE50. Blue Angel BSE50 4 halaman. Sewer ejector pump

Halaman Cetak

Operating Instructions And Parts Manual

For replacement parts or technical assistance,

call 1-888-636-6628

Please provide following information:

- Model number

- Serial number (if any)

- Part description and number as shown

in parts list

Ref.

No. Description

Part Number Qty

Volute

56603

Volute wear ring

23112

Impeller

SEE CHART

Shaft seal kit

56884-002

Seal plate

56604

Cover gasket

16855

Ball Bearings (Furnished with Motor)

Capacitor

3/4 HP to 2 HP

23126-002

1/2 HP only

23126-002

Locking cable tie

16634

Pipe Plug 1/4 Hex Socket HD.

16314

Lifting eye

23124

Power supply cord

SEP 5, 6, 7, & 8

23125-002

SEP 4

23163-001

1/2 - 13 UNC x 2 1/4 Hex HD.

16636

Motor housing

56605-001

www.blueangelpumps.com

Address parts correspondence to:

Blue Angel Pumps

101 Production Drive

Harrison, OH 45030 U.S.A.

Ref.

No. Description

Part Number Qty

Motor

SEE CHART

3/8 - 16 UNC x 1 1/4 Socket head

16798

1/2 - 13 UNC x 2 1/4 Hex HD.

16636

Discharge flange 2"

56606-001

Discharge flange 3"

56606-002

2" Discharge gasket

23101

3" Discharge gasket

23102

Washer

16635

1/2 - 13 UNC Hex nut machine screw

16637

Dielectric oil (1 gallon)

56435

Volute gasket

16735

MOTOR / IMPELLER CHART

H.P.

Motor Part Number

Impeller Part Number

1/2

3710-004

84341

3/4

3710-005

84342

3710-006

84343

3710-008

84345

Operating Instructions And Parts Manual

Installation

(Continued)

INSTALLATION BASICS:

1. NEVER lift this product by the

electrical cords.

2. Install pump in a sump pit that

fulfills the minimum size

requirements (24" minimum).

Construct sump pit of tile, concrete,

steel or plastic. Do not install a pit

smaller than recommended.

3. The unit should be located and rest

on a solid, level foundation. Do not

place pump directly on clay, earth,

gravel or sandy surface. These

surfaces contain small stones,

gravel, sand, etc. that may clog or

damage the pump and cause pump

failure.

Flood risk. If flexible discharge hose is

used, make sure pump is secured in

sump pit to prevent movement. Failure

to secure pump could allow pump

movement and switch interference and

prevent pump from starting or

stopping.

4. Thread the discharge pipe or pipe

nipple into the discharge flange

connection.

Three prong grounded

2" Discharge

outlet equipped with a

pipe

ground fault interruptor

2" Gate

Main

Valve

waste line

to sewer

Union

or septic

tank

Pump

Float switch

Figure 4 - Typical Installation

5. A check valve MUST be used in a

solids-handling system. Mount the

check valve in a horizontal position

or at a 45º angle with the valve

pivot on top. In a vertical position,

solids tend to lodge on the valve

flapper and can prevent it from

opening.

6. Drill a 1/16" hole in the discharge

pipe 1 to 2 inches above the flange.

This will prevent air locking and loss

of prime at startup. A gate valve

should be installed in the system

after the check valve. This gate

valve should be a full port valve

which will pass 2" solids or as

required by state and local codes.

The gate valve permits removal of

the pump and/or the check valve for

servicing (and will minimize

backflow mess).

7. (OPTIONAL) Install a union between

the check valve and the pump so

the pump can be removed with the

least amount of disturbance of the

piping.

8. Connect 2" rigid pipe to check

valve.

Upper level drainage

Cleanout

Washer

Dryer

Laundry tubs

Elbow

2" Check

Valve

Flange

Floor drain

Washer drain

Support pump and piping when

assembling and after installation.

Failure to do so could cause piping to

break, pump to fail, etc. which could

result in property damage and/or

personal injury.

9. Protect electrical cord from sharp

object, hot surfaces, oil and

chemicals. Avoid kinking the cord

and replace damaged cords

immediately.

IMPORTANT: Make sure there is

adequate room for tether switch to

swing freely during operation.

10. A pit cover must be installed to

prevent debris from clogging or

damaging the pump. All piping and

power cords will be brought

through the appropriate openings

in the basin cover. Do not modify

existing openings in any way.

All sewage basins must be vented to

prevent a build-up of methane gas.

Consult your local codes for proper

venting. DO NOT install venting in

locations classified as hazardous in

accordance with the National Electrical

Code NFPA 70.

Vent pipe

Lavatory

Shower