Blue Angel Pumps Professional BSP45 Petunjuk Pengoperasian dan Manual Suku Cadang - Halaman 4

Jelajahi secara online atau unduh pdf Petunjuk Pengoperasian dan Manual Suku Cadang untuk Pompa Air Blue Angel Pumps Professional BSP45. Blue Angel Pumps Professional BSP45 8 halaman. 24-volt backup sump pump

Halaman Cetak

Operating Instructions and Parts Manual

Pump Installation

(Continued)

3. A check valve will be required in

the discharge line of BOTH the

Main AC pump and the BSP45

pump to prevent recirculation of

water into the sump pit. System will

not function without two check

valves.

4. Cut a 4' section of 1

diameter rigid PVC pipe. Cement

" pipe to a threaded fitting.

Cement 1

" pipe into pipe

coupling. Attach 1

" pipe section

to the BSP45 discharge adapter.

5. Screw on to pump discharge.

Be careful not to

strip or cross thread

plastic fittings or check valves. Flex hose

is not recommended. Rigid PVC or metal

pipe is required for a permanent

installation.

6. Place the pump with the 4' section

of PVC pipe on the sump floor or

on an elevated surface if required.

7. Attach a rubber check valve (sold

separately) to the top of the

discharge pipe. This will allow the

pump or check valve to be removed

easily for servicing.

8. Duplicate the discharge piping

arrangement for the primary AC

pump if the existing discharge line

has to be adjusted to accommodate

a second pump.

9. Glue a 45º elbow to the short pipe

on the BSP45 pump. Glue a "Y"

adapter to the short pipe on the

existing pump, as shown in

illustration for Method 2.

10. Glue a short piece of PVC pipe

between the 45º elbow and the "Y".

NOTE: Check valves can be placed

directly in the pump discharge if

desired. However, for ease of

disassembly, it is recommended that

check valves be placed above the sump

as shown in Figure 3.

The remainder of the discharge pipe

installation will vary depending on

individual circumstances. Using sound

plumbing practices, route the

discharge pipe to an exterior wall by

the shortest distance.

www.blueangelpumps.com

" or 1

Batteries

Figure 3 - Method 2

Methods 1 and 2

Install float switch at least 10"-12"

above bottom of sump pit so that

backup unit turns on only when the

water level is higher than the normal

"on" level for main pump. Use the hose

clamps provided to secure the switch to

the discharge pipe. Make sure power

wires and hose clamp ends do not

interfere with float switch, pump inlet,

or main pump operation. Backup pump

must not be allowed to run dry.

PS/BC Installation

(PS/BC) indoors, in a well-ventilated

area. Do not expose PS/BC to rain or

snow. Do not use an extension cord. Do

not disassemble PS/BC. Be sure PS/BC

ventilation holes are unobstructed. If

PS/BC is dropped or damaged, do not

operate; return to manufacturer for

service.

(Ground Fault Circuit Interrupter)

receptacle to reduce the risk of fatal

electrical shock. Grounded receptacle must

be rated for at least 5 amps.

Floor

Joist

"Y"

Connector

45°

Elbow

PS/BC

Battery

BSP45

Box

Pump

remove pump fuse before connecting or

disconnecting battery.

1. Select a suitable position on the floor

ELEVATE PS/BC BY MOUNTING ON

WALL OR SETTING ON A SHELF. SLOTS

IN THE BACK SIDE OF PS/BC ARE

Use Power Supply/

AVAILABLE FOR WALL MOUNTING.

Battery Charger

Control Box Installation

to the PS/BC or battery could result,

and warranty will be void.

Dangerous hydrogen gas can be

Risk of electrical

shock! Use a GFCI

Rigid PVC

Pipe

Check Valve

(See Step 10)

Existing Pump

Always disconnect

AC power and

near the sump pit to place the battery

case. Be certain that the PS/BC power

cord will reach AC power, and that

the sump pump power cord will reach

the PS/BC. Make sure the battery case

vent holes are unobstructed.

If cables are

reversed, damage

released from batteries while

charging. Sparks can ignite the gas

in an enclosed space. Wear safety

goggles when connecting batteries.

Battery connections should be

made in a well-ventilated area.