Fleetwood L - 08 Buku Petunjuk - Halaman 5

Jelajahi secara online atau unduh pdf Buku Petunjuk untuk Blender Fleetwood L - 08. Fleetwood L - 08 6 halaman. Industrial blenders

Halaman Cetak
Fleetwood L - 08 Buku Petunjuk
4.1.3 Advices
In case of power shortage, immediately turn the machine OFF.
Use recommended or equivalent lubricants, oils or greases.
Avoid mechanical shocks as they may cause failures or malfunction.
Avoid penetration of water, dirt or dust into mechanical or electrical components
of the machine.
DO NOT modify original characteristics of the machine.
DO NOT remove, tear off or maculate any labels stuck on the machine. If any
label has been removed or is no longer legible, contact your nearest dealer for replacement.
READ CAREFULLY AND WITH ATTENTION THE SAFETY OR
OPERATION INSTRUCTIONS LABELS DISPLAYED ON THE MACHINE, AS WELL AS THE
INSTRUCTION MANUAL AND THE TECHNICAL CHARACTERISTICS WRITTEN INSIDE.
4.2 Safety Procedures and Notes Before Switching Machine ON
Carefully read ALL INSTRUCTIONS of this manual before turning the machine
ON. Be sure to be familiar with the instructions and that you have well understood
all information contained in this manual. If you have any question contact your
supervisor or your nearest Dealer.
4.2.1 Danger
An electric cable or electric wire with damaged jacket or bad insulation could
cause electrical shocks as well as electrical leak. Before use, check conditions of all wires and cables.
4.2.2 Advices
Be sure ALL INSTRUCTIONS in this manual have been thoroughly understood.
Every function and operational procedure have to be very clear to the operator. Contact your nearest
Dealer for further questions.
Any manual command (switch, button or lever) shall be given only after being sure
it is the correct one.
4.2.3 Precautions
The electric cable has to be compatible with the power required by the machine.
Cables touching the floor or close to the machine need to be protected against short circuits.
Oil reservoir has to be full up to the required level as indicated. Check level and
add oil if necessary.
06
IMPORTANT
1.3Technical Characteristics
Unit
L-02HD L-04HD L-06HD L-08HD
Caracteristics
[V]
110/220
Voltage
Frequency
[Hz]
50 ou 60
Power Rating
0,33
[HP]
Consumption
0,25
[kW/h]
Height
[mm]
610
Width
200
[mm]
Depth
[mm]
190
Net Weight
[kg]
Shipping Weight
[kg]
Rotation
[ rpm]
3500
(*) Frequency will be only the one indicated on motor characteristics label.

2. Installation and Pre Operation

2.1 Installation
The Heavy Duty Industrial Blender is to be installed onto a leveled surface
approximately 850mm high.
Before plugging in the machine check the voltage of the power supply: 110 or 220
V. Then adjust the machine voltage according to the power supply voltage using the Voltage Selector
Switch Nº07 (Pic.01) located at the bottom of the machine. Grounding is mandatory.
2.2 Pre Operation
Picture - 02
When installing the Cup Nº02 (Pic.01) in the machine be sure it is perfectly fitted. The
Cup can be fitted in the machine in any position; which guarantees a perfect
First of all check if the Heavy Duty Industrial Blender is firm in its position. It is
recommended to work with the machine in a flat surface with approximately 850mm of height.
Before using the machine all parts that get in contact with food must be washed
with running water and neutral soap. To clean your Blender read item 3.3 Cleaning on this Manual
(pag.4).
Table – 01
110/220
110/220
110/220
50 ou 60
50 ou 60
50 ou 60
(*)
(*)
(*)
0,5
0,5
0,5
0,37
0,37
0,37
655
745
760
245
245
260
190
190
230
7
9
9,20
9,40
8
10
10,30
10,50
3500
3500
3500
Heavy Duty
IMPORTANT
operation.
L-10HD
110/220
50 ou 60
(*)
(*)
0,5
0,37
850
270
230
9,60
10,70
3500
03